Fiberoptics
Field of optic fiber application.
-
Product
Fiberoptic Repeaters
-
*Cost effective task specific Fiber Optic Solutions for Satellite Radio and GPS over Fiber*End to end solutions complete with RF to Optical and Optical to RF component*Flexible powering options including DC over hybrid cable, local 48 VDC and AC*Utilizes industry standard fiber cables and connectors
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
LED Sensor
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
Product
Photonic Electric Field Sensor System
Model No. 200-04
-
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
Product
Fiber-Optic Measurement Technology
-
Fiber-optic sensors enable measurements in environments where electrical sensors reach their limits. Unlike electrical measurement methods, the purely optical measurement method is completely insensitive to environmental influences.
-
Product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-500
GPIB Cable
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
Product
Fiber-Optic Probes
Fiber-optic Probe
Designed with an unparalleled optical quality finish, Optomistic Products has developed a wide array of Fiber-optic Probes to accommodate your specific LED test requirement and mechanical constraints.
-
Product
HiCAM
-
The HiCAM is a gated intensified high-speed high-sensitivity imaging camera. It has an integrated fiber-optically coupled image intensifier, which offers a unique combination of high speed and sensitivity down to single photon level. Because the HiCAM does not need high intensity light sources, it is suitable for use in low-light level conditions.
-
Product
Laboratory Centrifuges
-
Centrifuge systems are designed for the development, test, evaluation and calibration of accelerometers and a variety of inertial devices. Centrifuges provide a cost-effective solution for simulating high-"G" environments in the laboratory. They support testing of devices such as MEMS-based Inertial Measurement Units (IMUs), low-cost quartz or silicon sensors, Ring Laser Gyros (RLGs), Fiber-Optic Gyros (FOGs), fuzes and crash sensors.
-
Product
Optoelectronics
-
Renesas provides a wide range of optoelectronic devices, including IC output photocouplers (optocouplers) featuring a high response from 1Mbps to 15Mbps, as well as general purpose transistor output devices featuring high isolation voltage, high temperature operation and compliance with various international safety standards. For motor drive applications, dedicated photocouplers provide high isolation voltage, high temperature operation, high output current, and high-speed switching. These are complemented by a diverse range of ultra-high speed devices for fiber-optic applications, as well as solid state relays (OCMOS FETs).
-
Product
Multifunction Platform
OSICS
-
The OSICS multifunction modular platform offers the highest flexibility and largest choice of plug-ins required in fiber-optic component and system testing, particularly for DWDM system evaluations.
-
Product
S2 Spectra Sensors
ULP-S2 WBI/V
LED Sensor
The ULP S2 Spectra Sensor tests for LED intensity, and for any color in the visual spectrum, plus white. The S2 Spectra Sensor is well-suited for the test of “boundary” color LEDs, as it can unambiguously and repeatedly distinguish between not only adjacent visual colors such as green and yellow, but it can determine different hues of the same color such as yellow and amber, regardless of LED intensity. Implemented in a unique and customizable 2-Part solution, the S2 Spectra Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Output Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: Typical response time: <10mS capture time; <100mS overall response timefor color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
