Digital Input-Output
Input/output of digital values.
-
Product
SparkFun 16 Output I/O Expander Breakout
SX1509
-
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
Product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
-
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
Product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
-
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
Product
EMX-75XX
Digital I/O Module
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
Product
PMC Digital IO Board
MS 1815
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
Board
Arduino Micro
-
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
Product
Motion Software & Utility
-
The Automation Product Software SDK (APS SDK) is an all-in-one solution with an optimized uniform interface to access all supported ADLINK machine automation products. The APS SDK features rich, powerful application-oriented motion functions that co-work with components such as system platform management, field bus communications, general digital input/output, general analog input/output and support for various counters/timers. With ADLINK machine automation series products that support APS SDK, machine makers can build and deploy applications easily and quickly with a universal tool, saving on TCO and enabling faster time to market.
-
Product
64-Channel VME Digital Input/Output Module
V250
-
The V250 is a single-wide, 6U VME module that provides 64 non-isolated channels of digital input/output. Each 16-channel bank shares programmable pull-ups and input thresholds with a range of 0 to +10 volts.
-
Product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
-
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
Product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
-
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
Product
Digital Input / Output Data Acquisition (DAQ) Products
-
In many cases, we only need to know a simple status about the device we are trying to collect data from, whether something is true or false, on or off, in one position or another. In these cases, we can determine what we need to know using a digital input, or control these things by a digital output. Digital I/O can fit into many applications.
-
Product
PCI 24-Bit Digital I/O Cards
PCI-DIO-24D/H
-
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
-
Product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
-
96 Channel Isolated Digital Input / Interrupt Output Module
-
Product
64 Channel Isolated Digital Input/Interrupt/Output Module
DP-VME-3636
-
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
Product
96-CH High-Driving DIO Card
PCIe-7396
Analog Input Module
The PCIe-7396 is a 96-bit parallel digital input/output (DIO) card esigned for industrial applications. The plug and play feature of PCI Express Bus architecture makes it easy for users to install the PCIe-7396 on their systems quickly.
-
Product
64 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3069
-
DP-cPCI-3069 provides 32 Channel Digital Input / Interrupt and 32 Channel Digital Output with isolation. 32 Channel Inputs and 32 Channel Outputs are divided into groups of 16 channels each and are routed to rear I/O only.
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
-
Product
Digitizers/Oscilloscopes
-
From entry-level to high-end, data acquisition to digital input/output, ADLINK provides a diversity of modular instruments with market-leading price/performance ratio, for bigger and better measurement and automation systems. Now high-speed digitizer, switching, simultaneous data acquisition, high-density multi-function data acquisition, analog output, digital multimeter, and arbitrary waveform generator categories are all available.
-
Product
256 Channel Digital Input / Interrupt Output Module
DP-VXI-3099
-
DP-VXI-3099 is a high density module that provides 256 channels of digital input/interrupt and/or output for large scale digital input monitoring and control.
-
Product
32-CH 80 MB/s High-Speed Digital I/O Card
PCIe-7300A
Digital I/O Module
ADLINK PCIe-7300A is an ultra-high-speed digital I/O card. It consists of 32 digital input/output channels. High performance designs and state-of-the-art technology make this card ideal for a wide range of applications, such as high-speed data transfer, digital pattern generation and digital pattern capture applications, and logic analyzer applications. Trigger signals are available to start the data acquisition of pattern generation.
-
Product
96-CH High-Driving DIO Card
PCI-7396
Analog Input Module
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
Product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
-
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
Product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
-
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
C Series Voltage Output Module
Input/Output Module
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with US Type Connector
HSL-DI16DO16-US
Input/Output Module
*16-CH digital input and 16-CH digital output*Shrounded-type connector*Isolation Voltage: 2500Vrms*Higher output current up to 90mA/channel*Easy installation and wiring
-
Product
C Series Relay Output Module
Input/Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
Digital Expansion Board
MSXB 013
-
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
