Isolated Digital Input Cards
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
PCI-6517, 32-Channel, ±30 V, Sink Outputs, Bank-Isolated Digital I/O Device
779083-01
Digital I/O
The PCI-6517 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6517 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6517 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
Digital I/O
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
Mini PCI Express
MPCIE-A429
Interface Card
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
Product
Low Thermal Input Cable
34102A
Digital Cable
Use this 1.2-m shielded, 4-conductor connector only with the 34420A Micro Ohm Meter; terminated in copper spade lugs.
-
Product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2223-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.447-04
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 8 Channels, 80 MS/s on 16 Channels, 16 Single-Ended Inputs, 8 True Differential Inputs
DN2.596-16
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
16-Ch Isolated Digital I/O Module With LED
ADAM-5055S
Digital I/O Module
I/O Type: 8 DO & 8 DIOptical Isolation: 2500 VdcPower Consumption: 0.68 W (Typical)16-channel
-
Product
High-Speed A/D 14-Bit Digitizers
Digitizer
GaGe 14-bit resolution digitizer models divide the input voltage range into 16,384 different digitization levels, which improves the delectability limit by a factor of 4 over the 4,096 levels of a 12-bit resolution digitizer model.
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
Interface Card
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
Digital I/O Switch Card - 96 Open Collector Channels in 12 Groups of 8 Bits Each
1260-14/14C
Switch Card
The Astronics 1260-14 Digital I/O Switch Card provides 96 open collector channels in 12 groups of eight bits each. With the open collector version each independent group can utilize a separate internal or external pull-up supply up to 32VDC.Each channel can be configured as an input or an output and individually controlled in the asynchronous mode, or be synchronous with other channels.
-
Product
1 Meter Long SCSI Cable with 100 Pin Connector
U2903A
Digital Cable
The Keysight U2903A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2903A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
NI-9470, 5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module
787089-01
Digital Module
5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module - The NI‑9470 is a digital output module that features proportional valve drive control. You can use the NI-9470 to perform pulse width modulation (PWM), dither control, and current readback. The NI‑9470 features eight output channels compatible with signals from 5 V to 30 V and transient overvoltage protection between the output channels and the backplane.
-
Product
Quad Port Fiber Gigabit Ethernet PCIE Express Server Adapter With Intel® I350 (Advantech Form Factor). Ideal For Multi-Port Network Deployments.
PCIE-1131
Network Interface Card (NIC)
Intel® I350 Controller4 1GbE SFP portsPCIe Gen.2 x4 host interfaceAdvantech small form factor that is smaller than low profile form factorsSupports multi-mode fiber (SX) and single-mode fiber (LX) modulesSupports SR-IOV based virtualization
-
Product
PCIe Thunderbolt 3 EON Express 12-Bit Digitizers
Thunderbolt 3
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-01
Frequency Input Module
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
Product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
Digital I/O
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
50 MHz 32-CH High-Speed Digital I/O Card
PCIe-7350
Digital I/O Module
ADLINK's PCIe-7350 is the advanced version of hot-selling PCI/PCIe-7300A featuring high-speed digital I/O with 32-channel bi-direction parallel I/O lines. The data rate can achieve up to 200 MB/s through the x1 PCI ExpressR interface. The clock rate can support up to 50 MHz internal clock or 100 MHz external clock, which is ideal for the applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
AXIe High-Speed Digitizer/Wideband Digital Receiver, 12-bit, 3.2 GS/s, 8-ch, FPGA Signal Processing
M9703B
Digitizer
Based on the AXIe standard the M9703B is an 8-channel, 12-bit digitizer/wideband digital receiver, able to capture signals from DC up to 2 GHz at 1.6 GS/s. A channel interleaving capability allows waveform acquisition at up to 3.2 GS/s with exceptional measurement accuracy. The M9703B also provides real-time data processing, large FPGA and customizable I/O interfaces. Detailed explanations can be found in the firmware options section of the datasheet.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4I.2212-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Low-noise 14-bit Digitizer
ADQ214-DCLN
Digitizer
The ADQ214-DCLN digitizer features dual channels, 14-bit resolution, 400 MSPS capture rate and is optimized for highly accurate low noise measurements. The ADQ214-DCLN is ideal for phase noise measurements and wideband IQ-receivers.
-
Product
PCIe-6612, PCI Express, 5 V, 8-Channel Counter/Timer Device
782351-01
Digital I/O
The PCIe‑6612 performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS-compatible digital I/O. The PCIe‑6612 can perform three simultaneous high-speed DMA transfers.
-
Product
PCIe Razor Express 16-Bit Digitizer
Digitizer
The GaGe Razor Express16XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 200 MS/s with true Effective Number of Bits (ENOB) of 11.7-bits with 10 MHz input.
-
Product
Embedded MXM GPU Module with Embedded NVIDIA RTX™ A1000
EGX-MXM-A1000
Graphics Card
- NVIDIA Ampere Architecture- Standard MXM 3.1 Type A (82 x 70 mm)- PCIe Gen 4 x8 interface- 2048 CUDA® cores, 16 RT Cores, and 64 Tensor Cores- 6.66TFLOPS peak FP32 performance- 4GB GDDR6 memory, 128-bit- 192GB/s maximal memory bandwidth- 5-year availability
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
DN2.221-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786168-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
780173-01
Voltage Input Module
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
Product
PXIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785590-01
FlexRio Digitizer
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
