Isolated Digital Input Cards
-
Product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
Digital I/O
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
PXIe High-Speed Digitizer/ Wideband Digital Receiver, 12-bit, 3.2 GS/s, FPGA Signal Processing
M9203A
Digitizer
The Keysight M9203A is a low noise, 12-bit PXIe high-speed digitizer/ wideband digital receiver with programmable on-board processing. With a wide analog bandwidth, this high-speed digitizer is ideal for applications requiring wideband signal capture and very high dynamic range. The M9203A is a dual-slot 3U PXIe 12-bit wideband digital receiver running at 3.2 GS/s, up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large XilinxFPGA that can implement different functionalities depending on the selected firmware option. Dedicated functions can also be implemented on board, allowing support of various applications. Furthermore, Keysight is supporting the deployment of custom processing algorithm on this digitizer with the U5340A FPGA development kit. Integrating algorithms minimizes the need for additional circuitry and exploit the full density and speed of the digitizer.
-
Product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
Digital I/O
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
sbRIO-9239, Non-Enclosed, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780875-01
Voltage Input Module
Non-Enclosed, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the sbRIO‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range. Non-enclosed modules are designed for OEM applications.
-
Product
PXIe-4305, 24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module
783868-01
Analog Input Module
24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4305 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
Isolated AC Voltage Input Module
ADAM-3112
Voltage Input Module
0 ~ 450 VAC to 0 ~ 5 VDCAC voltage measurement1,000 VDC isolation between output and power2,500 VAC isolation between output and inputInput impendent: 2 MohmMulti input modesAccuracy: ±0.1% FSRFlexible Din-rail mountingOperates from a single +24VDC
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-01
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PCI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, PCI Digital I/O Device
778792-01
Digital I/O
The PCI-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up … states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PCI-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
Isolated Digital I/O Card
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
Handheld Digital Multimeter, 4.5-digit
U1252B
Digital Multimeter
The Keysight U1252B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits on the bench or in the field. Key capabilities include manual and automated data logging to both DMM and PC. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1252B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1252B, you are well equipped to perform thorough troubleshooting of any faulty circuit.
-
Product
PCI Express Graphic Card with NVIDIA® Quadro® P2200
Quadro-E PEG P2200
Graphics Card
The Quadro-E PEG P2200 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1280 CUDA cores, 5GB GDDR5 onboard memory and support for up to four 5K (5120x2880 @ 60Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
-
Product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
Digital I/O
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
22 Bit / 1 MS/s Waveform Digitizer
WFD22
Waveform Digitizer
The WFD22 is a 22 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. It combines superior dynamic performance with a very high DC accuracy.The module features fully differential inputs to reduce common-mode level disturbances. It can also be used in Single Ended mode where an internal DC-offset source sets the midscale level.
-
Product
8-Ch Isolated Digital Input Module
ADAM-5052
Digital Input Module
Digital input level: Logic level 0: +1 V max.Isolation voltage: 5000 VRMSPower consumption: 0.27 W (max)Channels: 8
-
Product
Razor Express 16XX CompuScope 16-Bit, 200 MS/s, PCIe Digitizer / Oscilloscope
Digitizer
The GaGe Razor Express16XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 200 MS/s with true Effective Number of Bits (ENOB) of 11.7-bits with 10 MHz input.
-
Product
PXIe-6548, 200 MHz, 32-Channel PXI Digital Waveform Instrument
781012-03
Digital Waveform
PXIe, 200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6548 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6548 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
NI-9228, ±60 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module
783861-01
Voltage Input Module
±60 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module - The NI‑9228 performs differential analog input. With channel-to-channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. The NI‑9228 is simultaneous sampling with two options for filtering: a low-latency filter or a 50/60 Hz rejection filter. The low-latency filter enables users to use this module in industrial or control applications while getting better external noise rejection.
-
Product
RF Digitizer With 6.5 GHz Bandwidth
ADQ7WB
Digitizer
ADQ7WB is an RF digitizer with an analog input bandwidth of 6.5 GHz. It supports highly linear wideband data capture, and utilize Teledyne SP Devices' proprietary ADX technology in order to ensure industry-leading spurious-free dynamic range (SFDR).
-
Product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779372-01
Voltage Input Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
PXIe-6547, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument
781011-03
Digital Waveform
PXIe, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument—The PXIe‑6547 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 100 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6547 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
16-Ch Isolated Digital Input Modules
ADAM-5051S
-
50 Vmax Input Voltage2500 Vdc Optical Isolation70 Vdc Over Voltage Protection16-channel
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
Digital I/O
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
PCI-4070, 6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device
778275-01
Digital Multimeter
The PCI‑4070 is a high-performance DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PCI‑4070 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PCI‑4070 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
PXIe-6544, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument
780992-03
Digital Waveform
PXIe, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument—The PXIe‑6544 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXIe‑6544 can sample digital waveforms at up to 100 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6544 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
Network Interface Card
XMC477RC
Interface Card
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Full DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285
PCI Card
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer (10K points) for trajectory planning which is designed in DSPSupports E-Gear, and helical interpolationSupports E-CAM providing 256 points to describe the CAM profiles which buffers located in DSPHardware emergency inputWatchdog timerPosition latchPosition compare triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPProgrammable interruptSupports gantry mode by semi-closed loop pulse train controlRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
