Charge Amplifiers
A high-gain voltage amplifier with negative, capacitive feedback for converting a charge into a low impedance output voltage.
-
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
Amplifier Built-in Ultra-slim Photoelectric Sensor
EX-10S
-
Panasonic Industrial Devices Sales Company of America
Like the EX-10 Series, with the dimensions of only 14.5 x 3.5 x 10mm, the EX-10S Series Amplifier Built-In Ultra-Slim Photoelectric Sensors are among the smallest and narrowest Sensors worldwide. This "S" version with a thinner beam allows the detection of small objects within a very narrow detection zone.
-
Product
PWM Amplifiers
SA X-Series
-
MCS high power brushless motor drives combine high bandwidth with high current for demanding direct drive applications up to 100KVA. Backward compatibility with all MCS drives..
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
RF POWER AMPLIFIERS
BSA Series
-
RF Input: N-f, standard on rear panelRF Output: standard on rear panel<1 kW N-f<3 kW 7-16-f<5 kW EIA 1 5/8Mains Supply: Line Power:<1000 VA 100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA 200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA 3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter: via status displayAmbient Temperature: 0 ... +45 °CStorage Temperature: -20 ... +85 °CRelative Humidity: up to 95% (non-condensing)Operating Altitude: up to 2000 m above sea levelVibration and Shock: MIL-STD-810 GCooling: forced air with integral blowerair intake from front, air exhaust at rear
-
Product
Dual Channel HV Amplifier with Phase Inverter
A800DI
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
Operational Amplifiers
Op Amps
-
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
Product
Static Generators, Charging Bars and Pinners
-
The Generator/Bar System enables you to bond similar or dissimilar materials and holds materials in place, eliminates air pockets and wrinkles in multi-layer products, prevents plastic films from wandering on rewinders or shrinking on cooling cylinders, and increase production speeds.
-
Product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
-
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
Product
High Speed High Voltage Amplifier
WMA-300
-
The WMA-300 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-300 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications. Two WMA-300 amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Amplifiers
-
Instead of cascading a set of narrowband amps, use a single amplifier from Keysight and enjoy ultrabroad bandwidths - like 0.01 to 26.5 GHz, 0.045 to 50 GHz, and ranges in between. But the best thing about Keysight broadband amplifiers is what they eliminate and reduce: noise, crossover networks, and multiple power supplies.
-
Product
Handset Power Amplifiers
-
Broadcom Handset Power Amplifiers support different operating modes (CDMA, UMTS, LTE, and GSM/EDGE) and multiple frequency bands offering premium performance in a very small form factor.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Tower Mounted Amplifiers
-
*Available twin and single TMA configurations*Low band, high band & dual band units, including AWS & WCS*High linearity, dual duplexed, light weight design*AISG 2.0 compliant
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
Voltage Controlled Amplifiers
-
Teledyne Microwave Solutions (TMS) offers a variety of high-performance voltage controlled amplifiers operating over a 5 to 2500 MHz range. These VCAmps feature an AGC range of 20.0 - 50.0 dB and Response Times from 3 – 25µs. TMS has a broad range of component products to meet your demanding needs.
-
-
Product
100mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
Broadband Power Amplifier
PAS-00210-60
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 51.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
Low Phase Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
Product
Millimeter Wave Amplifiers
-
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Programmable USB Hub with 4 Charge Ports
-
The USBHub2x4 is a programmable USB 2.0 compatible hub featuring 4 device downstream ports with standard USB type-A receptacles and each port is capable of delivering up to 2.5A simultaneously. With two host (upstream) connections using usb mini-B connectors, the USBHub2x4 is perfect for environments where multiple devices need to be shared or switched between two host computers. E.g.: software regression testing, iPhone software development and validation, Android software development and validation, USB device regression testing, manufacturing testing, device burn-in testing and USB device charge-curve testing.
-
