OMICRON electronics
Specialization in power system testing.
- 1-800-OMICRON
1-713-830-4660 - 3550 Willowbend Blvd
Houston, TX 77054
United States of America
-
Product
CMC test Set Extender
RXB1
-
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
Product
3-in-1 Test System
CIBANO 500
-
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
Product
Software for System-Based Protection Testing
RelaySimTest
-
RelaySimTest is a software solution for system-based protection testing with OMICRON test equipment that takes a novel, future-oriented approach: the test is independent of relay type and relay manufacturer and the often very extensive parameter settings. Instead, it completely focuses on the correct behavior of the protection system. This is made possible by simulating realistic events in the power system.
-
Product
Resonance Circuit for GIS Testing
CP RC
-
For HV testing OMICRON’s CPC 100 + CP RC are directly connected to the voltage transformer of the GIS, forming a resonance circuit. This reinforced “Power VT” is an integrated part of the GIS. So the need for draining and refilling any SF6 gas is eliminated. Acting as both the measuring and controlling device, the CPC 100 injects the required energy.
-
Product
Three-Phase Relay Test Set
CMC 353
-
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
Product
Hybrid Signal Analyzer
DANEO 400
-
DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a substation.
-
Product
Portable Protection Test Set and Calibrator
CMC 430
-
The CMC 430 is the preferred choice for test engineers in cases where excellent transportability is needed and three currents up to 12.5 A or six voltage outputs are sufficient. Its low weight of just 8.7 kg / 19.2 lbs, and robust design with its edge protection predisposes the device to every outdoor and indoor use.
-
Product
Partial Discharge Measurements
MPD 500
-
The MPD 500 simplifies routine factory partial discharge measurements for electrical insulation systems. Engineered with OMICRON's long time experience, the MPD 500 is optimized for routine tests in high throughput environments.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
Product
Three-Phase Test System
TESTRANO 600
-
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
Product
Universal Test Set for Recloser Controls
ARCO 400
-
ARCO 400 is a smart and rugged testing solution for all recloser controls. It provides the fastest way to perform simple manual trip and close checks. Using the OMICRON Smart Connect technology, ARCO 400 is capable of detecting recloser specific test adapters.
-
Product
Protection Testing Library
-
The OMICRON software technology including the OMICRON Control Center, XRIO, and LinkToXRIO enables users to create specific test templates which adapt automatically to the actual relay settings. This functionality is the technological basis of the Protection Testing Library (PTL), a comprehensive test template library for a wide range of protection relays.
-
Product
Mobile, Hardened Test Set
MBX1
-
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
Product
Relay Test Set and Universal Calibrator
CMC 256plus
-
The CMC 256plus is the first choice for applications requiring very high accuracy. This unit is not only an excellent test set for protection devices of all kinds but also a universal calibrator.
-
Product
Protection Test Set
COMPANO 100
-
COMPANO 100 is the universal and easy-to-use solution for all types of basic testing duties in electrical energy systems. Controlled electronic sources allow the user to obtain exactly the desired value and to output signals with variable frequencies and other signal forms, automated ramps, and pure DC.
