-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
PXI 8 Trib Daisy Chain Switch 75 Ohm 96 Way
40-792-701
-
The 40-792/793 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data. Traffic is sequentially Daisy- Chained through all tributaries (or any selection of tributaries), modules can be cascaded to test any number of tributaries.
-
Product
Active FET Probe Kit 1.2 GHz, 10x, ±40 V
CT4121
-
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design.
-
Product
Automotive Test System
LABCAR
-
The LABCAR product family comprises software, hardware, and models suitable for integration into tailor-made testing systems that fit perfectly into existing processes. Deployable from the earliest to the latest phases of development, the LABCAR family provides for efficient verification and validation of embedded systems and software.
-
Product
Short Pulse High-Frequency Laser Marker
LP-RV SERIES
-
Panasonic Industrial Devices Sales Company of America
The LP-RV Series FAYb Laser Marker features:- Short Pulse 20W Fiber Laser Offers Excellent Mark Contrast On Difficult To Mark Plastics And Various Other Materials- Optional EtherNET/IP Or ProfiNET Interface Adaptor Card- Modular Laser Oscillator System Makes Servicing In The Field Possible - Direct Connection To Panasonic PV230 Vision System For Mark Verification, Auto-Targeting, And Other Machine Vision Functions- Compact IP64-Rated Marking Head For Use In Harsh Environments- Compliant With FDA Regulations, GB Standard, KC Mark, Machinery Directive (Declaration of Incorporation), EMC Directive, RoHS Directive
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Other Material Analyzers
-
GAOTek portable material analyzers deliver instant, relevant data for quick decision making in critical situations. Combining advanced technologies with an incredibly easy-to-use interface, our portable analyzers provide rapid, reliable chemical identification and material verification to increase throughput, increase quality and reduce risk. It can be used in any location, field environment or weather condition.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm
50-294-024
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
-
The optional PSL-3424-QT feature license opens up two important productivity tools in the PSL-3424 platform. PSL-3424 Quick Test is a fully automated PSE functional test covering between 2 and 8 PSE ports in a test cycle with average test times on the order of 10 seconds per port tested. The Chained Data Test user interface allows rapid construction and verification of test setups used in “snaked data path” testing of PSE’s with user specified loads and optional LLDP power negotiation on each test port.
-
Product
Zero-footprint Timing Analysis For Critical Software
RapiTimeZero
-
*Collect timing metrics from systems that produce branch traces* Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Analyze timing behavior of libraries without source code
-
Product
ATSC 3.0 Broadcast Stream Verification
StreamScope XM Verifier
-
The Windows®-based Verifier web app receives, tests, and records ATSC 3.0 broadcast streams from RF, Ethernet, and file inputs. With Verifier, you can monitor real-time graphs and charts of bitrates, signaling tables, RF parameters, packet errors, subframes, PLPs, and other KPIs.
-
-
Product
100 amu CIS Analyzer
CIS300
-
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
Product
Databus-to-Network Interfaces
OBB2
-
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
LSI Functional Verification Services
SpecInsight
-
The keys to functional verification are “verification strategy” and “highly complete verification item extraction.” Our functional verification services emphasize highly complete verification item extraction while also generating test benches and functional scenarios, random verification, and even functional coverage to meet customer demands by providing these services from a wide variety of angles. By implementing functional verification on the RTL and C models designed by customers from a third-party perspective, we improve quality of customers’ circuits.
-
Product
Hand-Held Test Solutions
RXT Series
-
With extreme modularity and an open platform concept, the RXT defines the test set of the future. The RXT''s capability to combine multiple technologies into a rugged modular platform increases the productivity of technicians who are responsible for the installation, verification, and maintenance of today''s complex services.
-
Product
MPI Automated Probe Systems
-
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
Product
PAT Check Box
369A910
-
The only check box to provide comprehensive verification of 17th Edition and PAT test equipment. The Powercheck tests for full earth continuity, insulation, resistance, RCD trip time, RCD trip current, touch current and flash test verification.
-
Product
Moisture Analyzer Series
3050
-
The 3050 series of moisture analyzers utilizes AMETEK’s proven, accurate quartz crystal microbalance (QCM) technology. Built-in verification provides operators with increased measurement confidence.
-
Product
In-depth Execution Time Analysis For Critical Software
RapiTime
-
*Timing analysis (inc. WCET) for Ada, C & C++ on-target & host**Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
Powered Device Analyzer for 802.3at & 802.3bt
-
The One-Box solution for 802.3 Ethernet Powered Device testing and verification including flexible emulation of PSE behaviors, scalable feature configurations, and plug’n play testing using a Windows PC.
-
Product
BSDL File Validation
-
Corelis offers services to validate the accuracy of Boundary-Scan Description Language (BSDL) files that characterize the boundary-scan functionality of semiconductor devices. These services include validation of a device's BSDL file while the chip is still in development and BSDL file accuracy verification against actual silicon.
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
Product
32-bit PCI Bus Extender
SKU-001-0X
-
The 32-bit PCI Extender was designed to support the development, debugging and verification of 32-bit PCI boards. The extender provides a complete PCI debugging platform that allows easy access to logic signals; it has over-current protection, and supports hot-swap operation.
-
Product
Optical Polarization and Dispersion Solutions
-
Test & measurement capabilities for analyzing polarization properties of optical signals are indispensable in todays optical R&D-labs and manufacturing floors. The Keysight N778x Polarization Analysis and Control series offers high speed instruments for high performance characterization and verification of optical components and sub-systems.
-
Product
EL & VI Tester
REOO RO-EV2400A
-
REOO RO-EV2400A EL & VI Tester is designed for PV module manufacturing lines, enabling fast EL and VI inspection for hidden defects and electrical quality verification.
-
Product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
-
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
