LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
-
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Digital CC and CV DC Power Supply
DC3005
-
The DC Series Power Supplies are with high stability and high accuracy. The voltage and current can be adjustable and can output costant current or constant voltage. They are suitable to supply DC Power for the standard lamp and the large power LED. Other voltage and current DC Power Supply can be designed according to customer’s request.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
Absorption Probe
ASD12-N
-
The ASD12-N absorption probe has a durable LED light source for direct installation into laboratory bioreactors and disposable bioreactors for measuring cell growth and optical density. The probe is available in three different lengths to fit any vessel and is suited for sterilization / autoclaving procedures.
-
Product
ISA POST Code Display
post2b
-
Post2b = ISA POST code display, not RoHS compliant (can be considered test equipment, not subject to RoHS). Spec? During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h. Use post2b to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size?
-
Product
ESD SURFACE RESISTIVITY METER (WITH 10 LEDS)
-
Simply place the meter on the surface of the material that requires measuring.Press the green test button. The meter will then light the appropriate LED from 10 to the power of 3 to 10 to the power of 12 Ohms per square or insulative.
-
Product
Dual Telephone Line Tester
NT-6006
-
This tool is for testing the condition of dual telephone line jacks. Multicolor LED indicator light alerts to okay line, reversed line, AC Voltage present and dead line. Fits in shirt pocket.
-
Product
Miniature High Resolution Underwater Color CCD Camera
L3C/LCC-720-L
-
The Teledyne Bowtech L3C/LCC-720-L miniature high resolution underwater colour CCD camera (with six integral high intensity LEDs) provides a low cost solution to general underwater viewing and observation, down to 1,000, 4,000 or 6,000 metres in confined spaces.
-
Product
USB3 Vision Cameras
xiQ
-
*Ultra compact mini camera- Only 26.4 x 26.4 x 21.2 mm and mere 27grams (1)*Cool - Low power consumption with 1.0 to 1.8 W and minimal heat dissipation*Fastest - High speed, high frame rate: 500fps at VGA and 90fps at 4Mpix resolutions*AIA standard - USB3 Vision standard compliant*Supported - USB3 under Windows 7 and 10, macOS, Linux, ARM and various Machine Vision Libraries*Industry standard interface - Compatible with USB 3.1 Gen1 SuperSpeed specification*Powerful potential - 5 Gbit/s interface 400 MB/s data throughput*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Cost efficient - Excellent value for the price, low TCO and fast ROI*Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Easy deployment - Range of accessories and widest hardware and software interoperability*Time proven - In production since the end of 2011*User friendly - Intuitive and simple to use API, easy switch from C to CS mount and more*Highly Customizable - Available in Board level (single PCB) and with different connector types
-
Product
Total Flux Measurement Systems
-
LED’s and Luminaires must be characterized and tested for brightness and color, for production quality control and also for R&D. The Gamma Scientific Total Flux Measurement System combines our accurate Radoma Spectrometer and an integrating sphere for total flux (total power) and color measurements of LED, micro LED and Luminaires. Measurement parameters include spectrum, lumens, total power, peak and dominant wavelength, CRI, CCT, FWHM and other optical properties.
-
Product
LED Tester For Ultra High Power
-
Electrical Testing: Forward：VF、DVF、VFD、IF、DIF Reverse：VZ、DVZ、IR、DIR AC：VAC、IAC、WAC、PFOptical Testing: can test LOP in cd/mcd/W/mW/lm... from different optical components Wavelength λp,λd,λc,hw,purity,(x,y),CCT,CRIFour-wire measurement and contact resistance in case of deviation. Auto polarity identification and preheat function.Compatible mechanical interface.Optional ESD static test system.
-
Product
Plug-In Power Supplies
-
VECTOR Electronics and Technology, Inc.
Standard PCI output Voltages : 5.0V, 3.3V, +12.0V, -12.0VHot swap, N+1 redundancy with internal OR-ing diodes.99 power factor corrected AC 90-264V input DC 36-72V (48V nom.), or DC 18-32V (24V nom.) Current sharing on 5.0V and 3.3V outputs Power & Fault LED indicators to faceplate Excellent performance
-
Product
Compound Semiconductors
GaAs and InP substrates
-
Sumitomo Electric Industries, Ltd.
GaAs substrates (compound semiconductors) are used for smartphone power amplifiers and switches, LEDs (illumination, decoration, indicators), and solar cells. InP substrates are used for optical communication modules, etc.
-
Product
Probe Series
GEMINI Series
-
Micro LED (µLED) is a disruptive optical technology breakthrough in the display industry. Micro LED displays offer tremendous potential for consumer/ display/ automotive applications because they are brighter, faster, and longer life compared with other emissive devices.
-
Product
White Light LED Illumination System
pE-300lite
-
CoolLED's pE-300liteis a simple white light LED illumination system that offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. The pE-300lite Light Source can be fitted directly to the microscope or specified with a liquid light guide. The system is a mercury-free alternative that is safer, more controllable, and repeatable than conventional high-pressure gas discharge illuminators. Spectral coverage is from the UV (DAPI excitation) to the Red region (Cy5 excitation). The system is perfect for hospital and regular research laboratory environments and is affordable within consumables budgets.
-
Product
Synchro And Resolver Angle Position Indicator
AP-501
-
The AP-501 is a high accuracy, auto-ranging, broad band synchro and resolver angle position indicator. The synchro or resolver angle is displayed on a bright 0.56 inch LED display. The indicator maintains a accuracy up 0.03 degrees even with synchro or resolver phase shifts up to 45 degrees over a frequency range of 47-300 Hz. The 800B301 is a low profile rack mounted synchro/resolver angle position indicator with 360 degree offset capability via front panel thumb wheel switches.
-
Product
Ultra-low Power NDIR CO₂ Sensor
CozIR®-LP2
-
The CozIR®-LP2 is an ultra-low power NDIR CO₂ sensor using state-of-the-art solid-state LED optical technology. The low-power LEDs are manufactured in-house, giving GSS complete control of the CO₂ sensor signal chain.
-
Product
Interface Terminals
-
Panasonic Industrial Devices Sales Company of America
Panasonic's RT-3 Series 4-Point Terminal, Unit Relays are slim, space-saving and have four independent points on a base which contribute to a more compact control panel or interface terminal. These Relays can be mounted on a DIN rail or mounted directly and all are equipped with an LED display to allow easy confirmation of operation.
-
Product
SparkFun ESP8266 Thing
Dev Board (with Headers)
-
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
Economy Model Vertisocket™
Series 800 and 822
-
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
-
Product
Pocket Autorange Multimeter
MT-1508
-
Comply with CE EN61010-1 CATIII 600V Safety rated.Comes with a backlight, 3 1/2 digits 1999 counts, great to understand reading.Auto range functions provide accurate, easy to use Display with backlight.Non contact ACV detectorPocket size design for easy carrying.Built-in LED flash light.Extra function: Auto power off, low batter indication, Data hold, Over range indication.
-
Product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Mini Multimode Power Meter and Mini LED Source
-
The KD Optics Mini Multimode power meter and Mini LED source are designed for the 850nm and 1300nm testing of multimode links, fibre continuity testing, connector testing, transmitter power testing etc.
-
Product
Pulsed Lasers and LEDs
-
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Spectroradiometer
Spectrascan® PR 788
-
The SpectraScan® Spectroradiometer PR-788 Extended Dynamic Range is JADAK’s ultra-sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Product
RJ45 Connectors
-
*Multiple Platforms Available, 1×1, 1xN, 2xN, Vertical Mount, Offset, Low profile*CAT3 to CAT5e Connectors Available*With & Without LEDs*With & Without Shields*Extended Temperature -40°C to +85°C*THT, Pin-In-Paste & SMT Options
-
Product
Multi-Battery Tester
MBT-1
-
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
