-
Product
AIIM Test Charts (Scanner/Microfilm/Digital/ Copier)
-
AIIM Test Charts (Scanner/Microfilm/Digital/ Copier) by Applied Image - Motion-Rotary Target, Planetary-Static Target, Small Area Target/AIIM MS-303-1980, Small Scanner Resolution Target , Copier Test Array, Rotary Test Target/AIIM X113, Film Strip Target, Eastman Kodak Copier/Scanner Digital Test Target, Small Color MTF Target
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
-
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
Test Handler
JOT M5
-
Simple, cost-effective way to automate PCB and pallet based testingSafe, reliable product handlingQuick-adjust ease: no product-specific partsFaster handling of smart productsIndustry 4.0 autonomous interconnectivityTruly scalable for growing test needsReusable, application-specific test boxesM-TestBoxes compatible with M1 handlerBoxes are fully independent, just pull out from M5 rack and use in off-line testingFail product separation to integrated magazineSpacious service-friendly constructionErgonomic workspaceTouchscreen UI with base statistics and service capabilityEasy start-stop operabilityAutomated width adjustment
-
Product
Micro Test Tubes
-
Shandong Drick Instruments Co., Ltd.
Length: 50mm, capacity is less than 0.8ml, apply WZZ-2S (2SS), SGW-1, SGW-2 and other automatic polarimeter
-
Product
Test Cell System
qCf FC25/100
-
The quickCONNECTfixture with an active fuel cell area of 25 cm 2 has been an integral part of our product portfolio since 2006. The excellent properties and the patented design of the cellFixture offer enormous advantages in the characterization of cell-internal components for fuel cells and electrolysis.
-
Product
LEAK TEST MANAGER SOFTWARE
-
Leak Test Manager is a software application for PC compatible with Windows XP, 7, 8 and 10 that allows interfacing ForTest equipment to a computer via an RS232 connection (or Ethernet if optional is available on the instrument)
-
Product
Longbow Launcher / LEA Test Set
TS-201B
-
The TS-201 is a state-of-the-art I-Level and Depot level test set for MIL-STD-1760 and legacy armament systems including launchers and bomb racks.
-
Product
Test House Services
-
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
Product
Multimeter Test Probes
-
Multimeter Test Probes, Voltmeter test leads,with the Parrot™ Clip Invention provide precise, HQ, accurate, reliable contacts and connections. Parrot™ Clips with HQ leads and banana plugs or other connectors are the best solution for DDM, analog multimeter for high voltage measurements as well as for high current measurements. Measurements with multimeter test probes require both: Hands-on direct point contact and grip on, Hands free removable connection.
-
Product
DC Hysteresis Graph Test System
DX-2012H
-
Automatic measurement of the demagnetization curve of permanent magnetic material such as ferrite, AlNiCo, NdFeB, SmCo, etc. Accurate measurement of the magnetic characteristic parameters of remanence Br, coercive force HcB, intrinsic coercive force HcJ and maximum magnetic energy product (BH)max.
-
Product
Website Test Automation - Software Testing for Agile Teams
Usetrace
-
In Usetrace you automate cloud computers to test your site. How to create accounts, order products and post comments. Cloud computers then automatically repeat these traces, testing your site the way your customers would use it—with real major browsers. Traces run periodically on your site, and every time you update the code. If bugs are found, Usetrace alerts you immediately before your customers experience them and business gets impacted.
-
Product
Accelerometer & Platform Test Bench
mS 1115
-
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
Product
Test Equipment For IEC 62133
-
designed for the battery thermal abuse test for IEC62133-8.2.2. The fire-proof dual-chamber has dimension 10" x 10" x 8", which can be heated up to 180°C via an independent temperature controller with +/- 1°C accuracy.
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
Modular Hydrostatic Test System
-
Our modular hydrostatic test chambers are designed with open ends to accommodate the connection to similar units for the purpose of lengthening the enclosed test area. The modular test system starts with a base unit with complete pump system, gauges and controls mounted on the 60” x 24” x 18” test chamber. If longer test lengths are required, simply add another test chamber to double, triple or quadruple the test length area. Specify your particular requirements at our Customization Page.
-
Product
Swagelok-Type Air Battery Test Cell
STA1
-
STA1 Swagelok-Type Air Battery Test Cell is designed for solid-state battery, liquid battery or in-situ electrochemical research where stable assembly pressure, reliable sealing and repeatable cell geometry are important. It supports laboratory-scale testing, method development and custom battery fixture projects.
-
Product
Test Lead Holder For Wires Up To 0.320In (8.13mm) Dia
4408
-
Test Lead Holder for Wires Up to 0.320in (8.13mm) Dia
-
Product
Electric Vehicle Module Test System
FTV
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
-
Product
Electroacoustic Test
-
CRYSOUND offers comprehensive and expert electroacoustic measurement solutions for a broad spectrum of consumer electronics, including headphones, microphones, and speakers. These solutions are characterized by powerful functionality and robust stability.
-
Product
Battery Test Equipment
-
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
-
Product
Highly Accelerated Life (HALT) Test
-
HALT consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated life testing is performed to identify design weaknesses and problems prior to production. HALT subjects equipment to overstress conditions at a level which does affect life, but offers an advantage by reducing the design and development phases of a program.
-
Product
Plug Pin Durability Test Device
IEC60884 Fig30
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig30 plug pin durability test deviceSuitable for checking the tightness of the plug pin,Check the tightness of the plug pin according to the standard, and customize the pin hole gauge of other national standards.
-
Product
In-Circuit Test Systems
-
Keysight offers leading board test solutions for electronics manufacturers to tackle a wide range of PCBA test access and coverage issues for today's complex printed circuit assemblies.
-
Product
In-Circuit Testing and Test Engineering
Teradyne Z1890
-
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
Product
EMC Test System
-
An electric product might cause the malfunction to other electric appliances by discharging the emission noise from it, or is oppositely caused the malfuction by the emission noise from other electric appliances. The former is checked by the EMI test and the latter is checked by the EMS test. The international standard like the CISPR standard is provided so that such an accident should not happen, and the manufacturer must declare by themselves beforehand that their product meets the standard. The generic name of the EMI test (Electro-Magnetic Interference) of the emission measurement and the EMS test (Electro-Magnetic Susceptibility) of the immunity
-
Product
Automated Meter Test Set
Model 2130
-
The TransData Model 2130 is a fully automated, computer controlled electricity meter test set designed for on-site accuracy testing and revenue certification of high-accuracy, multi-function energy meters to meet rigorous PUC, Sarbanes Oxley and ISO testing requirements.
-
Product
Test Automation
-
Write tests in plain-speak and refactor fearlessly so your test suite adapts as your application evolves. Gauge’s pluggable architecture allows you to customize your environment so you can write tests in the language and IDE of your choice.
