Laboratory
-
Product
Asphalt Testing Equipment
-
ELE international manufactures a comprehensive range of field and laboratory asphalt testing equipment to ensure compliance with quality and performance specifications. Traditional methods of binder content analysis involved the use of solvents, but due to environmental concerns ELE has developed an Asphalt Binder Analyser which uses an ignition method and thereby avoids the use of harmful solvents. Loss on heating and a rolling thin-film oven are used for testing bitumen, flash and fire point are measured with the Cleveland Flash Cup Apparatus, and the Ring and Ball test enables the measurement of the softening point.
-
Product
Photoluminescence Spectrometer
FLS1000
-
The FLS1000 sets the standard in both steady state and time-resolved photoluminescence spectroscopy for both fundamental research and routine laboratory applications. The system is a modular fluorescence and phosphorescence spectrometer for measuring spectra from the ultraviolet to the mid-infrared spectral range (up to 5,500 nm), and lifetimes spanning from picoseconds to seconds. All of this can be achieved through various upgrade routes, either at the time of order or in the future. Whether you are studying photophysics, photochemistry, biophysics, biochemistry, material or life sciences, the FLS1000 will enable you to reliably and accurately measure luminescence spectra and kinetics using state-of-the-art sources, detectors, acquisition techniques, quality optics and precision mechanics. The large sample chamber will house practically any type of sample accessory.
-
Product
Ohmmetry
-
From 0.1 µOhm to TeraOhms, every AOIP ohmmeter or resistance meter covers a very large spectrum of applications, providing high quality instruments for resistance tests, electrical continuity and insulation tests. Depending on the ohmmeter, measurements can be performed either on site or in laboratory.
-
Product
Precision Pressure Transducers
-
Precision and digital pressure transducers, somemtimes known as precision pressure sensors, convert pressure into an analog or digital signal proportional to the pressure being sensed. A precision pressure transducer (also referred to as a pressure transmitter) are used to monitor and or control sensitive pressure processes. They can also be used as high accuracy transfer standards or as a factory working standard for testing or calibrating a variety of pressure measuring instruments. With an accuracy as high as 0.008 % of reading, these pressure transducers can be found in laboratories or in production environments where a high degree of precision and accuracy are required. Each transducer is calibrated in Mensor's 17025, A2LA certified laboratory.
-
Product
Benchtop pH/ORP Meter
LAQUA PH2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Portable Dissolved Gas Analyzer
Myrkos
-
To make informed decisions on site, you need fast and reliable data. Myrkos portable gas analyzers provide laboratory quality DGA data where you need it, when you need it. In remote locations, to confirm monitoring data, or whenever on-site diagnosis is required, Myrkos portable gas analyzers provide results as accurate as a lab through our proprietary Shake Test® syringes.
-
Product
Portable Automated Measuring System
PG-350 P-AMS
-
For situations when you can only take measurements in the field, but you want the same precision that you get in the laboratory: HORIBA presents the Portable Automated Measuring System - PG-350 P-AMS.The HORIBA PG-350 P-AMS offers the same accuracy and reliability of laboratorymeasurements in a portable and durable unit, that is light and has a faster response time.With a shortened warm up time, a high visibility touch screen, high accuracy in measuring crucial components in the field and the durability to facilitate mobile measurement, the HORIBA PG-350 P-AMS is the analyzer system of the future.
-
Product
Oscilloscopes
-
AEMC Instruments proudly introduces the first hand-held portable two- and four-isolated-channel 600V Cat. III Oscilloscopes on the market with 12-bit resolution. Featuring five complimentary tools in one - an Oscilloscope, FFT Analyzer, TRMS Multimeter, Harmonic Analyzer and a Recorder - all in a rugged and ergonomic hand-held instrument. They are the perfect tools for both laboratory and field testing.
-
Product
Measuring Devices For Nanoindentation
-
With our measuring devices, you can determine the mechanical properties of thin coatings reliably and accurately. From protective paint coatings to hardness of PVD coatings: We have the right solution for you. We offer you powerful and easy-to-use measuring instruments for the laboratory and production. You can choose from a wide range of accessories to adapt your device to your individual requirements.
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
Electricity Meter Test Equipment
ELMA
-
The Electricity Meter Test Equipment ELMA due to modular concept enables to tailor specifications to specific laboratory demand. The available power and the maximum current of 240 A of extremely pure synthesized 4-quadrant test signal covers the needs of both precision and high capacity testing laboratories.
-
Product
Integrating Spheres & Absolute Flux Integrators
-
Photometric Solutions International Pty Ltd
PSI’s LF series integrating sphere photometers are widely regarded as excellent quality, robust equipment for industrial or laboratory applications.
-
Product
Constant Distance SECM
VS-STYLUS
-
In collaboration with SENSàSION, we are pleased to offer the Soft Stylus Probe contact mode technique developed by Professor Hubert Girault and co-workers of the Laboratory of Physical and Analytical Electrochemistry (LEPA) at the École Polytechnique Fédérale de Lausanne (EPFL) for constant distance SECM. The probe technology offers the following benefits:
-
Product
Lab Equipment
-
Sper Scientific offers a range of the highest quality equipment for numerous laboratory applications. Our lineup includes: calibration kits, silicone pipet fillers, ultrasonic cleaners, pocket microscopes, laser pointers and more.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Laboratory Air Data Test Sets
-
DMA is a leading manufacturer of Air Data Test Set models for laboratory use achieving the highest accuracy and resolution. The MPS46 is digitally controlled through a keyboard, it uses very high accuracy pressure sensors, with a special characterisation for maximum accuracy (for static channel < 2 feet at sea level). Pressure resolution of 0.2 Pa. is also achievable. The intuitive user interface with touchscreen display ensures that all the functions are controlled with a minimum of key presses . The ADTS can be used in avionics ATE systems (rack height only 2U) for automated pitot-static testing through RS232, USB, Ethernet or GPIB/IEEE488. An internal pump or external rack mounted pump unit can be supplied as an option.
-
Product
Inspection Microscope
-
This compact, lightweight and ergonomic Inspection Microscope is specifically designed for inspecting ferrule and fibre end faces in the field or the laboratory. The microscope provides dual-illumination, both coaxial and oblique; to produce the highest-quality image detail and superior view of fibre end face cleanliness and core condition.
-
Product
ccVPX Card
EXC-4500ccVPX/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-4500ccVPX/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
Hot Dipping Simulator
HDPS
-
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
Product
Stopwatches + Timers
-
Sper Scientific professional laboratory stopwatches and timers use only highly accurate quartz crystal movements. All models are available with an N.I.S.T. traceable Calibration Report.
-
Product
USB Power Sensor - 10 MHz to 18 GHz, True-RMS Average
GT-8553B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Energy Detector Laser Energy Meters
11QE25-LP-S-MB
-
11QE25-LP-S-MB energy detector provides a unique combination of high damage resistance and high speed. It also offers very good linearity with power and a versatile mounting system. It is right for many pulsed lasers. It is right for many OEM, manufacturing and laboratory uses.
-
Product
Resistance Thermometry Bridges
-
By using built-in or external standard resistors, resistance thermometry bridges measure resistance ratios with high accuracy, which are indicative of the temperature, among other things. These instruments are not only used in the field of temperature measurement, but − due to their high accuracy − also in electrical laboratories.
-
Product
On-Site Field Testing & Evaluation
-
MET is a highly-regarded resource for electrical inspection agencies within the United States and Canada to assure compliance of unlabeled equipment in the field. Field evaluations are performed by MET Laboratories on unlisted equipment to support the Authority Having Jurisdiction.
-
Product
In-line ICP® Charge Converters
-
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
Product
Powered VME430 Crates
-
The CERN VME430 standard, often called "Nuclear VME", is an extension of the VME64 Standard and was introduced in 1980 by the European High Energy Physics Laboratory CERN. It is fully backwards compatible to VME/VME64.
-
Product
Tan Delta Test System
-
Precision measuring bridge is designed for determining the capacitance and dielectric dissipation factor of liquid and solid insulants, cables, capacitors, line transformers, generators, motors, bushings etc. Furthermore it can also be used for power loss measurement on shunt reactors or similar apparatus. This system is suitable for both low and high voltage measurement at line frequency. Measurement reports can be printed. This measuring equipment has been specially developed to maximise efficiency in production and quality control environments. Its outstanding accuracy also makes it suitable for laboratory and research applications.
-
Product
GC System
-
Agilent's Gas Chromatography systems provide modern laboratories with new performance expectations by increasing analytical performance, reducing cost of ownership, and saving capital expenditure investing. These benchtop, on-line, and portable GC systems (available for in-lab and field analysis) are all supported with Agilent's 10-year Value Promise Guarantee demonstrating our commitment to long-term reliability.
-
Product
Broad-Beam Ion Milling
-
Materials Evaluation and Engineering
Ion beam milling is a unique method of sample preparation that complements and significantly extends the capabilities of the traditional microscopy and metallographic laboratories.
