Wafer Probers
bring the wafer in contact with the set of wafer probes.
See Also: Probers, Wafer, Flying Probes, Thermal Chucks
-
Product
Flying Prober Test System
QTOUCH2204C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
Product
2D/3D Wafer Metrology System
7980
-
Chroma 7980 provides accurate and reliable profile information. 7980 adopts new BLiS technology and specially designed platform to achieve 2D/3D nanoscale measurement.
-
Product
MultiSite Test sockets and Wafer Level
-
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
Product
Wafer Inspection Machine
IV-W2000
-
The IV-W2000 is a wafer inspection machine that features on-the-fly scanning and inspection as well as automatic handling of 6/8/12-inch wafers. With the option to have a Chinese language UI, this machine is also known for being intuitive and user-friendly.
-
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Wafer Back Side Cooling System
GR-300 Series
-
The GR-300 Series can control gases used to cool the back side of wafers that are fixed in position by an electrostatic chuck system.The stability and accuracy of the GR-300 makes it ideal for controlling the flow of Helium and Argon in wafer cooling systems.
-
Product
Photonics Wafer Probing Test System
58635
-
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
Product
WAFER MVM-SEM
E3300 Family
-
The E3310 is a WAFER MVM-SEM* for next generation wafers, supporting 1Xnm node process development and volume production at the 22nm node and beyond. With its high-speed carrier system employing a dual arm vacuum robot, and low-vibration platform to improve measurement accuracy, the E3310 delivers high throughput and performance for wafer measurements. Its multi detector configuration and unique 3D measurement algorithm also enable stable, high-accuracy measurement of 3D transistor technologies such as FinFET. The E3310 makes a significant contribution to reducing process development turnaround time and improves productivity for next-generation devices.
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
Inline Wafer Testing
IL-800
-
Pre-process elimination of low-quality wafers using measured lifetime, trapping, and resistivity. Process control and optimization at dopant diffusion and nitride deposition steps.
-
Product
Wafer Mapping Sensor
M-DW1
-
Panasonic Industrial Devices Sales Company of America
To provide better safety and improved sensing accuracy, Panasonic studied the requirements for future Wafer Mapping Sensors to ultimately develop the LED Beam Reflective Type Wafer Mapping Sensor, M-DW1. This Sensor uses LEDs as a light source for safe operation and a 2-segment receiving element for higher accuracy in wafer detection.
-
Product
Wafer Test
-
Silicon Turnkey Solution, Inc.
Most foundries provide wafers already probed to a set of DC parameters at room temperature to ensure they meet a basic subset of the package-part specification. Beyond this basic set of tests, more rigorous testing is often needed to meet specifications requiring die to be 100 percent probed, identify and segregate devices with higher performance levels and guarantee that parts will perform to a certain specification level.
-
Product
Die-To-Wafer Bonding Systems
-
Several different D2W bonding methods are available and selected depending upon the application and customer requirements. In direct placement D2W (DP-D2W) bonding, the singulated dies are bonded to the target wafer one by one using a pick-and-place flip-chip bonder. Plasma activation and cleaning of the surfaces of the dies on the handler wafer are essential steps for establishing a high-yielding bond and electrical interface between the dies and target wafer. This is where the EVG320 D2W activation system comes in.
-
Product
Cable Tracer Prober M-CTP-240A
Cable Tracer Prober M-CTP-240A
-
Fuzhou Metricu Technology Co Ltd
Cable Tester, network tester
-
Product
Full Wafer Contact Test System
Fox 1
-
Unique cartridge technology uses full-wafer contactors combined with parallel test electronics to achieve single touch, full-wafer test
-
Product
Ambient Temperature Vacuum Wafer Chucks
-
6" (152mm) Vacuum Wafer Chuck for General Purpose Ambient Temperature testing with a Stainless Steel vacuum wafer surface
-
Product
Portable Wafer Probe Station
PS-5026B
-
High Power Pulse Instruments GmbH
The PS-5026B is a rugged portable wafer probing solution which has been designed for high reliability, compact size and minimum cost.
-
Product
Wafer Thickness Measurement System
MPT1000
-
Laser based Wafer Thickness and Roughness Measurement System designed by Chapman Instrument Inc., USA and OEM by Creden Mechatronic Sdn Bhd. A non-contact measurement system measures several parameters in a single system. (wafer & tape thickness, roughness, TTV, bump height, bow and warp measurements)
-
-
Product
In-Process Wafer Inspection System
7945
-
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
Product
Wafer Sorter and Inspection
SolarWIS Platform
-
Eliminating the opportunity for problematic wafers to enter cell manufacturing lines greatly improves output and yield. ASM AE’s wafer sorter features 3D area inspection capability to inspect wafer thickness, total thickness variation (TTV), saw marks, as well as wafer bow and warpage. SolarWIS also includes modules that can inspect for stain, geometry, micro-cracks, edge chips, resistivity, P or N conductivity and lifetime.
-
Product
Wafer Cathodoluminescence Microscope
Säntis 300
-
Attolight’s Quantitative CL-SEM offers “No Compromise” large field fast scanning simultaneous acquisition of SEM images, hyperspectral CL maps, and optical spectra. Smaller diameter wafers, or miscellaneously shaped substrates are manually loaded on intermediary 300mm susceptors subsequently handled automatically by the tool.
-
Product
Semiconductor Wafer Microscope Inspection System
MicroINSPECT
-
MicroINSPECT Semiconductor Wafer Defect Microscope Inspection System combines state-of-the-art robotics, intelligent microscopes and SITEview software to provide a flexible, easy-to-operate defect inspection platform for either micro or macro defect wafer inspection.
-
Product
Full Wafer Test System
FOX-1P
-
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
Product
Automated Semiconductor Wafer Optical Inspection and Metrology
SITEview Software
-
Microtronic SITEview Software is designed from the end-user operator’s perspective and is easy to use, fully featured, and modular. Applications include visual wafer inspection, OCR sorting, wafer defect review, second optical inspection, image storage and retrieval, laser marking, microscope interface, and GEM/SECS II communication and seamlessly integrates with EAGLEview, MicroINSPECT and MicroSORT.
-
Product
Non-contact Measurement Wafer Sorting System (Belt Drive Tranceportation)
NC-6800
-
*Non-contact measurement of resistivity, thickness and conductivity (P/N)*Number of cassette station can be changed by customers request*Eddy current method for resistivity, Electric capacitance method for wafer thickness*Temperature correction for silicon wafer function
-
Product
Wafer Demounting And Cleaning Machines
-
Demounting and cleaning to high throughput fully automatic ingot after cutting in the slicing machine and wire saw.
-
Product
Wafer Inspection System
AutoWafer Pro™
-
AutoWafer pro is our most advanced ultrasonic equipment for detecting defects in bonded wafers in a production environment, providing fast, high-resolution scanning of 200mm and 300mm bonded wafers.
