Elemental
of the periodic table.
-
Product
Configuration And Visualization Software
-
Schweitzer Engineering Laboratories, Inc.
SEL software helps you optimize the configuration and management of your device and system settings. You can also use it to display and analyze relay event data, element operation, and more.
-
Product
Quick Change Probes For Weld Seam Testing (ASTM)
SONOSCAN Q
-
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
Product
Normal Incidence Shear Wave Transducers
-
Single element normal incidence Shear Wave Transducers contact transducers introduce shear waves directly into the test piece without the use of refracted wave mode conversion. We recommend the use of our SWC shear wave couplant for general purpose testing.
-
Product
Silicon Drift Detector
Octane Elite (SDD) Series
-
The game changing advancements in the Octane Elite Silicon Drift Detector (SDD) Series take detector technology to the next level. This line of detectors incorporates a new silicon nitride (Si3N4) window, which offers remarkable improvements in low energy sensitivity for light element detection and low kV microanalysis. The Octane Elite Series also uses the widely praised CUBE technology, which yields high speed X-ray data processing within a smaller and fully vacuum encapsulated detector device.
-
Product
Speed Sensors
-
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
-
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
ACCUplace Grid Indexing Pattern
AP-G Series
-
Ensuring precise motion and positional accuracy is critical for a number of video analysis systems and automated measuring instruments. The AP-G series is ideally suited for calibrating such elements, in addition to its uses in determining stage squareness, and travel distance image analysis and visual inspection systems where precise motion must be calibrated and measured. All AP-G targets have number/letter indexed columns and rows for easy calibration and are offered on four standard materials; Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
Product
X-ray Fluorescence Spectrometer
-
X-ray fluorescence spectrometer that provides quick, easy elemental analysis using touch screen operation. It is equipped with functions for conventional qualitative and quantitative analysis (FP method, calibration curve method), as well as screening for RoHS elements. With a variety of both hardware and software options available, it is customizable to cover a wide range of analysis needs.
-
Product
On-site Oil Analyzer
MicroLab 30
-
MicroLab 30 is designed for fleets operating over-the-road vehicles or generator equipment. This analyzer best suited for companies interested in testing primarily engine oils to determine the serviceable life of the oil and the equipment condition. The MicroLab 30 analyzes six oil chemistry parameters along with viscosity to determine proper drain intervals. The standard 10 element version provides information on oil contamination and wear metal analysis to determine if mechanical issues exist. The MicroLab 30 can be upgraded to 20 elements if there is an interest to analyze oil additive levels as well as additional wear metals.
-
Product
ICP OES spectrometer (ICP AES)
-
SPECTRO Analytical Instruments GmbH
ICP OES spectrometer (ICP AES) for the rapid analysis of elements in a variety of matrices including aqueous, semi-conductor, petrochemical, soil, metallurgical and slurries
-
Product
Sensors
-
Murata pursued sensing functions making full use of MEMS and processing technology, and magnetoresistive elements including ceramic material technology in order to develop highly efficient and highly reliable devices, modules and systems.
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A
40-192A-012
-
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Gas Analysis
-
Our infrared gas detectors provide superior sensitivity and reliability that may be translated into a more effective early warning system when monitoring atmospheres for gases at trace levels. Our technology also offers the opportunity to perform sophisticated gas analysis. One example: To assure personal safety during a medical procedure, our gas detectors deliver a precise monitoring of the ratio of exhaled gases of a hospital patient who is under general anesthesiology. Another example, no canary need die in a mine if Dexter gas detectors are installed on the job. Infrared lead detectors, whether mobile or mounted, can be a critical element in your health and safety strategy at home and on the job, whatever life forms it is your responsibility to protect.
-
Product
LXI 1GHz 75ohm 32x16 Matrix
60-730-001
-
The 60-730 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-730 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
Product
FPGA PXI Digital I/O Card
GX3500
-
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs, as well as providing pin for pin compatibility with NI PXI 7811R and 7813R FPGA cards. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory.
-
Product
High-power Benchtop Sequential WDXRF Spectrometer
Supermini200
-
Elemental analysis of solids, liquids, powders, alloys and thin films. The new Supermini200 has improved software capabilities as well as a better footprint. As the world''s only high-power benchtop sequential wavelength dispersive X-ray fluorescence (WDXRF) spectrometer for elemental analysis of oxygen (O) through uranium (U) of almost any material, the Rigaku Supermini200 uniquely delivers low cost-of-ownership (COO) with high resolution and lower limits-of-detection (LLD)..
-
Product
Test Thorn Probe
CX-41
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Thorn Probe For testing accessibility in appliances with visibly glowing heating elements.
-
Product
Magnetic Float Type Liquid Level Gauge
HR9210
-
HighReach Measuring & Controlling System Co.,Ltd
The HR9210 magnetic float type liquid level gauge is a measuring instrument that reflects the measured liquid level or interface by the magnetic float as the sensing element and through the coupling of the magnetic float and the magnetic body in the display color strip.
-
Product
Controlled Impedance Field Solver
Si8000m
-
TheSi8000m is an all new boundary element method field solver , which builds on the familiar easy to use user interface in earlier Polar impedance design systems. The Si8000m adds enhanced modeling to predict the finished impedance of multiple dielectric PCB builds and also takes into account the local variations in dielectric constant on close spaced differential structures.
-
Product
DC Current Shunts
-
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
-
Product
Satellite & Payload Check-Out Systems
-
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
Product
LXI 1GHz 75ohm 8x8 Matrix
60-731-004
-
The 60-731 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-731 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
Product
Multiplexers
-
The range extends from Lumped Element Diplexers at 300 MHz through to 60 GHz devices based on BSC’s Exact Filter Technology. Our design experience and in-house production facilities have allowed us to construct Diplexers with near contiguous passbands meeting the most demanding technical requirements.
-
Product
S-GW Functional Tester
-
The LTE SGW Functional Tester provides a wrap-around test solution for the Serving Gateway by emulating all the LTE network elements surrounding the SGW (System Under Test). The S-GW Functional Tester emulates an LTE eNodeB and other Core Network entities such as the MME, P-GW, S-GW, RNC and SGSN. It tests the S1-u, S11, S5/S8 , S12 and S4 interfaces of the S-GW.
-
Product
AdvintRIO™ Reconfigurable I/O
SNAKEHEAD
-
The Snakehead platform employs aNI CompactRIO (cRIO) system consisting of an embedded controller, chassis, and NI C Series I/O modules.Snakehead systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to powerful real-time controller with a user-upgradable backplane that includes a high performance field-programmable gate array (FPGA). Snakehead provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These units are designed for ruggedness, reliability, and low power consumption. The heart of Snakehead systems is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module
-
Product
Angle Sensors
-
Angle sensors of the PRAS/PRDS series are based on a contact-free and absolute measurement principle. The position sensing element is a permanent magnet.
-
Product
X-Band Silicon Radar Quad Core IC
AWS-0104
-
The AWS-0104 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain during transmit mode, 21dB gain in receive mode, +15 dBm output power during transmit, and 3.4 dB NF during receive. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8V supply, and is packaged in a 56 lead 7x7 QFN for easy installation in planar phased array antennas.
-
Product
Build to Print
-
In today’s fast paced manufacturing environment, where time to market and cost competitiveness is key, having a manufacturing partner like ARC can be a valuable resource for your company. ARC has a build-to-print manufacturing capability with our unique ‘engineer-to-print’ philosophy to make sure precision manufacturing and final build accuracy is top priority for your module level or system level builds. ARC can support up to several hundred module level assemblies (CCA subassemblies, cabling, mechanical and paneling elements) with abilities to perform a variety of software, embedded tasks and functional testing including a mixed signal test capability using our in-house MSAT (Mixed Signal Automated Tester) platform. We have a thorough process created through the development of our own products and test solutions. We know the importance of having a regimented manufacturing process, augmented with engineering expertise to address challenges that come up with building complex, high-mix, medium volume products.
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
-
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
