Power Meters
See Also: RF Power Meters, Magnetic Field Strength Meters, Digital Power Meters, Energy Meter Test
-
Product
Single Phase And Three Phase Ageing Bench Type KP-S31000
-
Bofa Instrument & Equipment Co., Ltd
This ageing bench is used for ageing single phase energy meter and three phase emergy meter in meter manufacturer. It consists two parts: Power source and meter rack (single phase and three phase), usually we sugest 1 power source + 9 single phase meter rack (96 positions each) or 6 three phase meter rack (48 positions each).
-
Product
Laser Power Meters
-
Is used to measure the energy output of laser beams for testing or laser system applications. It uses detection sensor to determine the intensity of a laser beam’s energy output.
-
Product
Digital Power Meter
-
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
Product
Milliohm Meter
MO-100
-
Diagnose potential failure with the MO-100, portable battery powered milliohm meter. Quickly check windings opens or shorts in motors, generators and transformers, wire-to-wire connection resistances, heating elements testing and contact resistance in critical electrical connections.
-
Product
1000 A AC/DC Navigator Clamp Meter with Temperature
Amprobe ACDC-54NAV
-
The ACDC-54NAV clamp-on power meter offers AC/DC current measurements to 1000 A, AC/DC voltage to 1000 V, temperature capabilities, and wide jaws to handle large conductors up to 1.6″ (40 mm) for high voltage industrial environments.
-
Product
Power Meters andCalibration Cells
-
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
Product
E-Series Average Power Sensor
E9300B
-
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
VDSL Tester
X5008
-
X-5008 VDSL tester specially designed for slid line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on. X-5008 VDSL Tester also introduces the Optical Power Meter and Visual Fault Locator function into the unit, as well as the TDR function. It is one mufti-function tester with smart size, true color LCD and powerful management software as well as the 6600mAh rechargeable battery etc.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 6.5 GHz
N9934B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Entry Level Loss Tester
Model：OLT-20
-
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 9 GHz
N9935B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
EPM-P Series Single Channel Power Meter
E4416A
-
The E4416A single channel EPM-P series power meter, for peak, average, peak-to-average ratio and time-gated measurements, using the E9320 peak and average power sensors.
-
Product
Multifunctional Meter
CPM-12
-
CPM-12 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.Hardware can be option a a RS485 Modbus communication port.Auto wiring change (Note) via softwareCE and FCC approved
-
Product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
-
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
AC Power Source
SPS-100
-
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
-
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
Optical Power Meter
PM-102B
-
The PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-102 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
Product
NI-9242, 250 Vrms L-N, 400 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783107-01
-
250 Vrms L-N, 400 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9242 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, standard potential transformers, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9242 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta.
-
Product
Optical Power Meter
SAT-4E
-
Shaanxi Aitelong Technology Co., Ltd
SAT-4E optical power meter is an indispensable tool to identify fiber, measure fiber loss, verify continuity, and evaluate transmission performance, widely used in LAN, WAN, CATV, remote optical network, etc.
-
Product
Digital Power Meter
2406B
-
‧Simultaneous display of W, A, V (PF or Hz)‧True RMS V, A, W‧Auto calibration via computer‧Data Hold∕Range Hold function‧Hight immunity to external noise‧CT ratio (1～99)‧REF function (0.800 ～ 1.200)‧Aux. power is AC 90 ～ 260V, 50/60Hz‧RS-232 interface (option)
-
Product
Fiber Optic Multimeter
-
Combines the function of fiber optic power meter and fiber optic light source and the user can easily switch to choose the multi meter function via the control menu.
-
Product
Power Meter
EPM 6000
-
EPM 6000 is the industry's highest performance revenue grade panel meter. Based on the latest technology and an all new platform, EPM 6000 has a superior cost to performance ratio and significantly outperforms other metering products many times its price.
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
Handheld Optical Power Meter
JW3205
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3205 mini handheld optical power meter is the most lightweight and compact in size testing instrument. It features ease-of-use and economy advantages and can be used for absolute power measurement in optical fibers. JW3205 in combination with the JW3110 mini handheld light source become the most portable and advantageous testing pair.
-
Product
Dual Input Universal Power Meter
8542C
-
The Spanawave/Giga-tronics 8542C Dual Channel Universal Power Meter combines accuracy, speed, range and measurement capability.
-
Product
Optical Power Meter
HOPM-3205
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HOPM-3205 mini handheld optical power meter is the most lightweight and compact in size testing instrument. It features ease-of-use and economy advantages and can be used for absolute power measurement in optical fibers. HOPM-3205 in combination with the HOPM-3110 mini handheld light source become the most portable and advantageous testing pair.
-
Product
Power and energy calibrators
-
Three or single phase electric power/energy calibrator with power quality functions for calibration and testing of grid measuring appliance like power meters, power transducers or power quality analysers.
-
Product
Optical Power Meters
-
Optical power meters are technical instruments used to measure optical signal, something which is key in testing average power in fiber optic systems.
-
Product
Dual Channel Optical Power Meter
UC8202
-
The UC8202 Dual channel optical power meter offer superior performance for the test of DWDM components, AWG , WSS, OPM, PLC components, optical amplifiers, transceiver/receiver and other general purpose of fiber optical test and measurement applications
