Power Meters
See Also: RF Power Meters, Magnetic Field Strength Meters, Digital Power Meters, Energy Meter Test
-
Product
Power Meter
-
Beijing GFUVE Electronics Co.,Ltd.
One of the most useful and simple instruments to measure electrical power when no deeper analysis of the measured data is required.
-
Product
Handheld Optical Power Meter
JW3402
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3402 Optical Power Meter is a highly cost-effective portable power meter and it’s newly launched by the Joinwit Company. It can be used for the optical power measurement within the wavelength 800～1700nm. JW3402 also has a wide measurement range which is more than 70dB. It’s designed with the common wavelength calibration points, such as 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. The instrument is widely used in fiber-optic link construction, testing and maintenance.
-
Product
E-Series Average Power Sensor
E9304A
-
Refer to the E9301A for standard power sensor features Low frequency coverage (9 kHz to 6 GHz) for EMC/EMI test applications such as the radiated immunity test (IEC61000-4-3)High sensitivity (-60 to +20 dBm) and fast measurement speed to reduce the time taken to calibrate radiated field uniformity and EMC/EMI test receivers Measure transmitter power and receiver sensitivity at Very Low Frequency (VLF) to microwave frequencies Special option available to 18 GHz Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
50 MHz to 18 GHz USB Peak and Average Power Sensor
U2021XA
-
The U2020 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming.
-
Product
110 GHz Lightwave Component Analyzer
N4372E
-
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
Product
Lightwave Detector
N4377A
-
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
E-Series Average Power Sensor
E9300H
-
Measure the average power of all modulation formats Wide dynamic range power measurements from -50 dBm to +30 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Multi Circuit Power Meter (DIN rail)
AEM-DRK
-
The AEM-DRK multi-loop power meters are designed for multi-loop power measurement. It has 2 kinds of circuits which are single-phase 21 loops, or three-phase 7 loops. Also, it can be operated with different circuits, and applied on various occasions that will significantly reduce the cost.
-
Product
Power Sensors
-
KRYTAR's Power Sensors simplify your measurement equipment requirement when used in conjunction with KRYTAR's Model 9000B Power Meter for accurate and repeatable power measurements. The 9000B power meter with a 9500A Series power sensor offers the user exceptional measurement speed and accuracy at an affordable price.
-
Product
Variable Optical Attenuator - MATRIQ
-
The VOA MATRIQ Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fibre types and various wavelengths to suit a wide range of applications.With a stackable, space-saving design and intuitive software controls make it a valued addition to the optical lab or test bench.
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
PON Power Meter
TM70B
-
TM70B PON Power Meter (pon test instrument) is specially designed for PON network construction and maintenance which can be connected between OLT and ONT. The voice, data, video signal (1310/1490/1550) online can be measured synchronously and optical power value (1310/1490/1550) can be displayed with this meter. It’s a useful site test tool for the engineers of PON network and maintenance operators.
-
Product
Handheld Optical Power Meter
JW3211
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3211 optical power meter is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optic fiber networks. An Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, wide range of power measurement, high accuracy, user self-calibration function and reference power level storage.
-
Product
Portable Electrical Measuring Instruments in ABS Body
-
Supreme Instrument Laboratories
General Specification for Portable Ammeters, Voltmeters, Milliammeters, millivoltmeters, Micro Ammeters, Single phase Wattmeters, power Factor Meters, Dynamometer type Voltmeters, Ammeters etc. Housed in superior grade of ABS body, unique design, very strong in construction, unbreakable and very high insulation.
-
Product
Thermal Power Sensors
NRPxxT/TN/TWG
-
The R&S®NRP power meter sensors have long been recognized for delivering supreme precision and speed. The R&S®NRPxxT, R&S®NRPxxTN and R&S®NRPxxTWG thermal power sensors are especially used for complex measurement tasks where highest accuracy counts
-
Product
USB Power Sensor, 50 MHz to 24 GHz
U2002A
-
Fast and simple setup with plug-and-play USB connectivity. Eliminates the need for a separate power meter.
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
-
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
InGaAs Optical Power Head
81624C
-
The new 81624C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81624C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Optical Power Meter
HOPM-3211
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HOPM-3211 optical power meter is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optic fiber networks. An Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, wide range of power measurement, high accuracy, user self-calibration function and reference power level storage.
-
Product
EPM Series Single-Channel Power Meter
N1913B
-
The N1913B EPM series single-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
Product
Fiber Testing Kit
KI-TK056
-
1310/1550 nm source & power meter, Interchangeable SC connectors
-
Product
Portable Single Phase Power Factor Meter
-
Supreme Instrument Laboratories
Portable Electro-dynamometer type single phase single element Power Factor Meter laboratory type for horizontal use, housed in laminated wooden cabinet size 235 mm length x 200 mm width x 180 mm height, with detachable lid, black bakelite panel fitted with anti-parallax mirror scale, knife edge pointer, rubber footings, carrying handles, locking arrangements. The power Factor Meters are fitted with an iron shielded Electro-dynamometer type cross coil system.
-
Product
RF Spectrum Power Meter
SPM-50
-
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
Product
Multifunctional Meter
CPM-20
-
CPM-20 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.It provides maximum/minimum records for power usage and power demand parameters.Hardware standard built in a RS485 Modbus communication port.FCC and CE Approved
-
Product
Sound Level Meter - For Workplace And Environmental Noise
SONIK-SE
-
The SONIK-SE is a powerful sound level meter which is ideal for performing occupational and environmental noise assessments for a variety of applications.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
FieldFox Handheld Microwave Analyzer, 18 GHz
N9917A
-
18 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
Calibration Services
-
Mors Smitt has a professional calibration center. All electrical measurement equipment can be calibrated (for example; multimeters, current clamps, temperature meters, installation testers, power meters, safety testers, etc.).
-
Product
Scalar Network Analyzer
8003
-
The Spanawave Model 8003 Precision Scalar Network Analyzer combines a 90 dB wide dynamic range with the accuracy and linearity of a power meter in a signal instrument.
