-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Load Tester for D Type Durometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
Product
CPCI Or PXI Analog IO Board
MS 1808
-
*Bus Interface*PCI Bus Interface, 6U Form Factor*Facility for Calibrating all Output channels*Hot Swap facility*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PC104Z with FMC Board
PC104Z
-
Sundance Multiprocessor Technology Ltd.
PC104Z is based on the Xilinx Zynq UltraScale+ MPSoC family. This hardware is in PCIe104 form factor and adheres to its latest specification. It offers 4 Gen 2.0, x1 lane PCIe interfaces through a switch which allows 4 PCIe104 cards to be connected to the ARM on the Zynq which acts as the host. The board also offers 2 Gen 4.0, x4 lane PCIe connected to the PL parts which can act both as host and end points. The additional interfaces offered by this card can be seen under the Features tab.
-
Product
Meter Qualification Board
MQB
-
Power-up and apply load to electric watt-hour meters for functionality testing with TESCO’s multi-position MQBs. These boards assist with AMI Meter Certification process and AMI meter qualification and communication testing.
-
Product
Waveguide Loads
-
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
Product
Bench Electronic Loads
EL30000 Series
-
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
DB37 DIN-Rail Wiring Board
ADAM-3937
-
Low cost universal DIN-rail mounting screw terminal module for DAQ cards with DB37 female connectorCase dimensions (W x L x H): 87.2 x 112.5 x 51 mm (3.4" x 4.4" x 2.0")To Be Used With PCI-1713U, PCI-1715U, PCI-1718HDU, PCI-1720U, PCI-1730U, PCI-1733, PCI-1734, PCI-1750, PCI-1760U, PCI-1761
-
Product
Telemetry Shackle Load Cell
TS-3.0
-
The DLM Telemetry Shackle is a high strength marine grade wireless Load Cell. Manufactured from industry leading Crosby and GN shackles along with a stainless steel load pin, the DLM Telemetry Shackle offers reduction in weighing headroom with the flexibility of 2.4GHz licence free wireless load transmission.
-
Product
BASIC-programmable IoT Board
EM1001
-
Our flagship BASIC/C-programmable IoT board. Ethernet, as well as optional Wi-Fi and GPRS connectivity. Four serial ports supporting full-/half-duplex RS232, Wiegand, and clock/data modes.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
Robotic Sample Loading Systems
-
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
-
Product
TR G4x/msd, 3U OpenVPX™ server board
TR G4x/msd
-
TR G4x/msd is SWaP-optimized with excellent processing, memory and storage capabilities. Long life-cycle for rugged server applications in military, aerospace, transportation & test. Elma is a value added reseller for Concurrent Technologies.
-
Product
Board
ARDUINO UNO WiFi REV2
-
The Arduino UNO WiFi Rev.2 is the easiest point of entry to basic IoT with the standard form factor of the UNO family. Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a Bluetooth® Low Energy device sending data to a cellphone, the Arduino UNO WiFi Rev.2 is your one-stop-solution for many of the basic IoT application scenarios.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
Product
Arowana PCI Express SSD Board Family x1 PCI Express Gen 3 SSD Board
SKU-090-31-x1
-
The Arowana PCI Express SSD board is the smallest carrier board on the market. This PCI Express Carrier board was designed to expand modern motherboards or embedded systems that have a PCI Express interface. It can also be vertically installed in any 1U servers or appliances.
-
Product
Dual DC Electronic Load
3330F Series（40W~250W）
-
3330F Series Dual DC Electronic Load is a two load unit in one module. Each 3330F Series module has its own control and display panel, CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be remote controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
Bending Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
Are the best fit for many measuring tasks. Here, the signal, on principle, depends on the bending moment.
-
Product
PCI Express A/D Board
AD8-1500 Series - Dual 8 bit, 1.5 GS/s
-
The AD8-1500 series has one or two 1500 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
Load Length Meter
-
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
Product
DC Electronic Load Control Software
EES-100-xx
-
EES-100 Software controls all electronic load types. ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing
-
Product
Electronic Load
-
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
Product
PC-based Data Acquisition Boards
-
Data Acquisition and PlaybackPCI, cPCI / PXI : 32bit, 33MHz64 MB/sec data streaming2 OMNIBUS Modular I/O sitesExternal trigger & clockOn-board DDS timebase & timers/countersControlled from Windows or Linux based applicationHuge suite of C++ software componentsMMX optimized DSP analysis components
-
Product
460V / 18 Amp Load
EL08-460M
-
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 307V to 460V and is extremely cost effective.
-
Product
12-bit, 100KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3001-4
-
4 single-ended or 2 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Dry Dielectric RF Coaxial Loads
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
High Load Shear Strength Tester
HLST1000
-
This tester measures the shear force required to analyze the bonding strength of various bonding materials. It is possible to measure shear force up to 5000N for the purpose of bonding strength evaluation over a large area. An optional heating unit enables evaluation while the sample is heated.
-
-
Product
Beam and Singlepoint Load Cells
-
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
