Cables
See Also: Cable Assemblies, Cable
-
Product
“Floppy drive” Power Split Cable
SKU-043-06
-
Female 4-pin “floppy drive” power connector on one end, and 2 female 4-pin “floppy drive” power connectors on the other end on this cable.
-
Product
Connecters
-
Ideal for connecting boards and wires. Abundant variations for flat cables and loose wires, as well as MIL and DIN systems
-
Product
160-Pin DIN Female To 160-Pin DIN Female Switch Cable
782417-02
-
The SH160DIN-SH160DIN helps you connect to the PXI-2510 PXI Signal Insertion Switch Module or compatible PXI Relay Modules. You can use this cable to facilitate signal routing between instruments and devices-under-test (DUT).
-
Product
PXI 64x2 Matrix Module, 1-Pole, 2A, 60W
40-527-001
-
The 40-527, 40-528A and 40-529A are PXI single-pole matrices each supporting 128 cross points. The modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Product
Cable Diagnostic Tools
-
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
Product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
786341-01
-
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
-
Product
Additional Products: 8 Pin Power D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
-
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
4-Pin Power D-Type Male to Unterminated With Cut Ends, 2m
40-972-404-2m-MU
-
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
Cable 96-Pin Female to 100-Pin Male Micro-D, 2m
40-973B-096-2m-FM
-
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
Time Domain Reflectometer
TDR-420
-
TDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
-
Product
15-Pin D-Type Connectors & Cable Accessories
-
Our 15-Pin D-Type connector is used on PXI switching products to provide a medium density user connector solution.
-
Product
Cable Assembly, 160-Pin DIN41612, Female To Unterminated With Ferrules, 2m
40-972A-160-2m-FU
-
A range of DIN41612 cable assemblies with unterminated connections on one end. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
LXI Wired Trigger Bus Adaptors And Accessories
-
We manufacture LXI Wired Trigger Bus adaptors and accessories. These adaptors and accessories are designed to help debug a WTB system or provide conversion of signals to or from the WTB to products that do not support the WTB. LXI approved WTB cable assemblies and terminators are available to interconnect LXI devices that support the LXI Wired Trigger Bus extended function.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI
540072010240
-
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI
-
Product
32-bit PCI Test Backplane
SKU-014-01
-
The 32-bit PCI Test Backplane was designed to support production testing/debugging of PCI-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into four 32-bit PCI slots via 7 ft CAT6 cable. The PCI backplane is a versatile platform that allows you to test up to 4 PCI boards at the same time, facilitates easy access to logic signals, provides hot-swap compatibility, and per-slot overcurrent protection.
-
Product
26 Pin D-Type Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 26-pin D-type connector.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 0.5m
40-972-009-0.5m-MU
-
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
2 Meter Long SCSI Cable with 100 Pin Connector
U2904A
-
The Keysight U2904A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2904A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
Non-contact High Voltage Testing
-
Shanghai Beha Electronics Co., Ltd.
An ideal tool for checking the presence of AC high voltages and AC low voltages in cables, wall outlet, fuses......etc.
-
Product
Recloser and Sectionalizer Test Cables
-
OMICRON offers a comprehensive range of cable packages as an accessory to CMC test sets for testing various recloser and sectionalizer controls.
-
Product
4-Pin Power D-Type Cable, Male to Male, 0.5m
40-970-404-0.5m-MM
-
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable 96-Pin Female to 100-Pin Male Micro-D, 0.5m
40-973B-096-0.5m-FM
-
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
Modem
CDA3-35
-
Hitron Americas Technologies Inc.
The CDA3-35 is the perfect choice for cable operators who want to offer high-speed broadband access to their customer base economically. It delivers speeds of up to 1.2Gbps (32×8) with thirty-two bonded downstream channels over its DOCSIS interface. The CDA3-35 is an intelligent device that enhances its basic data transmission features with IPv6 support. This makes it especially suitable for the transmission of data based on this protocol.
-
Product
Pitot Static Tester / AoA TESTER
ADSE 744
-
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Product
Two 110/220VAC-to-48VDC Desktop-Style Power Supplies
TE3201
-
The TE3201 is comprised of two separate 110/220VAC-to-48VDC desktop-style power supplies. Together, they provide two isolated 48VDC inputs to power the TE3200. Interconnection is made to the front connector on the TE3200 via a screw-terminal/power adapter board (TE3202) and VGA extension cable that are included with every retail order (not included with OEM orders) for the TE3200.
-
Product
CDN - Coupling / Decoupling Networks
-
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
78-Pin D-Type Female Without Backshell
92-960-078-F
-
This connector is designed to allow users to directly terminate cables with soldered connections. 78-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m, 90º
A1604FT-C-0A050
-
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
