-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Needle Microprobe
MT-4
-
Fast-response 29 gauge needle probe with blunt tip, (needle length is 1cm) for instant readings. Good for instant skin temperature and surface temperatures, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
Needle Microprobe
MT-26/2HT
-
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Manual Test Adapter With Rigid Needles
-
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
2.5mm Test Rod Test Probe Needle
CX-4C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
Product
UV/IR Flame Detector for Hydrogen Apps
-
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
-
Product
Needle Microprobe
MT-26/6HT
-
Fast-response 26 gauge needle probe, (needle length is 6 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Flame Photometers
-
Flame Photometer applies the emission spectrum as the basic principle, which uses the flame heat and excites part of the atoms in alkaline earth metal. The atoms receive energy and transfer it to the old energy level. When the atom is at a normal energy level it releases the energy.
-
Product
Needle Hydrophones
-
Our high-performance needle hydrophone system consists of a range of interchangeable PVdF needle hydrophone probes, a submersible wide-band amplifier and a DC coupler.
-
Product
Needle Valves
-
Needle valves are designed for laboratory and industrial applications for regulating corrosive gases and liquids or for high purity service. They can also be used as bubble tight shut-off valves.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
Needle Microprobe
MT-23/3HT
-
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
-
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
Product
OptiStroke™ Needle Stroke Detection System
-
The patented OptiStroke system reduces product waste and confirms hot melt adhesive dispensing performance by verifying valve actuation and fatigue. Ideal for applications where product-yield loss is critical, the system is compatible with Nordson Universal™ modules, Speed-Coat™ modules and Harmony modules.
-
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
-
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Flame Detector
SMC 3100
-
The SMC 3100 Series Flame Detector utilizes a tri-spectra design (UV, IR and visible light spectrums) to provide continuous and reliable flame detection. The 3100 Series design provides the ability to detect flames from both hydrocarbon and non-hydrocarbon sources, making it ideal for a facility where the flame source could be generated from a variety of gases.
-
Product
Needle Microprobe
MT-29/5HT
-
Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Needle Microprobe
MT-26/4HT
-
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
