Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Integrated Modular Electromagnetic Modeling Suite
EM.Cube
-
EM.Cube® is an industry-recognized simulation suite for electromagnetic modeling of RF system engineering problems. It features several distinct simulation engines that can solve a wide range of modeling problems such as electromagnetic radiation, scattering, wave propagation in various media, coupling, interference, signal integrity, field interactions with biological systems, etc. Using EM.Cube, you can solve problems of different sizes and length scales, varying from a few microns in MEMS devices to several miles in large urban propagation scenes.
-
Product
32 Form C High Power Relay Module
DP-cPCI-4035
-
DP-cPCI-4035 is a cPCI-based 32-channel high power relay. It is designed as general-purpose module. Applications of this module include power routing, relay outputs for soft PLCs, automatic test equipment, hardware simulation and high current measurement routing.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k
40-293-031
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Product
Telemetry Simulators & Test Transmitters
-
Command Data Telemetry Simulators offer a dynamic way to create or change a PCM data stream on a word by word basis on the fly. This PCM data stream can be used to modulate an FM or SOQPSK RF output at S-Band or L-Band. In addition to simulating a new telemetry stream, the telemetry simulators can play back and loop an archived data file (which can also be changed on the fly) or create pseudo-random patterns.
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
Fault Insertion Unit
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
-
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
Product
NASA Battery Simulation System
-
DMC leveraged our established Battery Management System (BMS) Testing Platform to deliver an automated Battery Simulator System to a NASA research group. NASA needed this system to facilitate development of highly specialized battery devices. These battery systems were designed to provide mobile power for advanced electromechanical systems such as Robonaut 2, a dexterous humanoid robot created to perform a wide range of tasks to assist astronauts on the International Space Station.
-
Product
Loading Adjustable Drop Tester Machine
CX-DL15A
-
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
Product
Standard Weather Radar Test Panel
TA-3
-
Universal weather radar test panel with integral gyro simulator and monitor jacks. Discrete test jacks for common signals, altitude select switches and a dedicated connector for the RDS series radars. Click on picture for larger view.
-
Product
Sunlite Solar Simulators
-
- Gen III Optics for High Efficiency Illuminati- Infinitely Adjustable Irradiance, Reproducibly Settable- Class A AM1.5G Spectral Match- ASTM Class A stability- 50×50 mm Class B uniformity- Manual Shutter Included, Electronic - Shutter Optional- Uninterrupted testing with the prealigned lamps- HEPA filtered air cooling
-
Product
PXIe-7867, Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785570-01
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7867 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to the FPGA, you can quickly design for applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7867 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7867 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
50 Pin D-type Connectors & Cables
-
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Product
High Power & Voltage Pack Testing System
FTF
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
Product
Environmental Shock Simulation Machine For Drop Testing
-
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
Test Solutions
-
Our range of test solutions is far reaching, comprised of off-the-shelf test instruments and interfaces, standard automated test systems, and custom solutions for test, simulation, and training. Put our E2E focus and experience to work for you with these solutions: automated test equipment, maintenance trainers, and test management software.
-
Product
PCI BUS Interface Card
PCI301
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Test Lungs
SmartLung
-
The SmartLung product line offers a truly versatile and cost effective way of simulating the lung characteristics of infants and adults without effecting the settings and operation of the ventilator or anaesthesia machines.
-
Product
PXIe-7847, Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784144-01
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7847 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7847 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7847 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
Instrumentation
-
Test instruments, Switching & RFIUs, and Test, Simulation, & Avionics Interfaces.
-
Product
Finite Element Analysis (FEA) Solution
Femap
-
Siemens Digital Industries Software
Femap is an advanced engineering simulation software program that creates finite element analysis models of complex engineering products and systems, and displays solution results. Femap can virtually model components, assemblies or systems and determine the behavioral response for a given operating environment.
-
Product
TLP Tester lineup
-
Hanwa Electronic Ind. Co.,Ltd.
The tester can implement simulate operating characteristic of protective circuit In addition capable of the VFTLP test.
-
Product
Bally Waterproofness Tester
UI-FT20
-
Bally Waterproofness Tester is to test materials like coated leather, leather dynamic water penetration resistance ability. The material would be partially put in water and the bally water penetration tester would flex the sample in the water under certain speed to simulate material water resistance in daily work. Here for more Leather Testing Machine.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel, 2 Ω to 13.6 kΩ
40-297A-131
Programmable Resistor Module
The 40-297A-131 (PXI) and the 42-297A-131 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 13.6 kΩ, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Sand Dust Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
Multi-Scenario Simulation: Replicates desert storms, industrial dust ingress, and abrasive wear with programmable wind/sand profiles. Precision Particle Control: Cyclonic dispersion system ensures uniform particle distribution (ISO 12103-2025 certified). Durability: Hard-coated aluminum interior, wear-resistant seals, and self-cleaning filter traps. Smart Monitoring: Real-time particle counter, temperature/humidity logging, and AI-driven failure prediction. Energy Efficiency: Recirculating airflow design reduces energy use by 35% (ENERGY STAR® 2025 compliant).
-
Product
Portable Power Amplifier
PAV250Bip
-
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
