Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
-
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
Product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
Product
Developer's Studio for ATLAS
PAWS
-
PAWS Developer's Studio gives you the power to compile, modify, debug, document, and simulate the operation of ATLAS test programs in a Windows environment.
-
Product
Resistive Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Resistive load banks are an important tool for testing and verifying the performance of power systems such as generators, UPS systems and turbines. They simulate real-world electrical loads by dissipating power as heat through resistive elements.
-
Product
Solar Simulator Continuous Light
-
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
Product
Communication Data Logger
LE-270AR
-
LE-270AR is an Analyzer and Communication Data Logger of CAN/LIN. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on the PC. You can measure 2 channels of CAN/LIN communication lines and can simultaneously register voltage data of 4 external signals.Its power failure protection, waterproof, and low power consumption widens the usage of analyzer such as in the automation factories and other production factories.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-112
Fault Insertion Unit
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
ACARS CMU Simulator
-
Square Peg Communications Inc.
The SPCI CMU Simulator replaces the ACARS Communications Management Unit for end-to-end testing of the ACARS system. It communicates with an Inmarsat Classic Aero or SB-Safety Satellite Data Unit (SDU) via ARINC-429 to generate and receive ACARS traffic. The CMU Simulator is implemented as a Physical Layer Tester script, and can run on either a BPLT or a GDU. In addition, it can run on a standard PC using a special version of the GDU or BPLT software. In all cases, a suitable ARINC-429 interface must be present.
-
Product
Double-Roller Dynanometer
R 200/2 DIVIDED | VP 430004
-
Maschinenbau Haldenwang GmbH & Co. KG.
The double roller dynamometer R 200/2 DIVIDED with an eddy current brake on each roller set and pneumatic lifting beam is designed to measure the performance of trucks and stands out due to its extremely robust, durable and low-maintenance construction. The R 200/2 ensures highest measuring accuracy due to the power measurement at a constant rpm, speed or tractive force, including the towing power measurement. For tuning and adjustment tasks the load simulation is evaluated graphically. An extension up to a wheel power of 660 kW is optionally possible.
-
Product
BusTools/1553 BusTools Software Analyzer
-
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
Product
NI-9862, CAN Interface Module
781639-01
Interface Module
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 102kΩ
50-297-040
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
Simulator
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
Product
Direct conversion from cycle driven simulation data
Test program generator
-
Direct conversion from cycle driven simulation data (ATPG scan patterns) (WGL/TDL/STIL) to tester. TDL/WGL/STIL to tester conversion Supports STIL ext 0,1,2 constructs Easy to use and cost effective conversion solution Optimize tester resources usage Supports advanced tester features (Such as Xmode, Multi-port etc’) Compress and minimize vectors count Allow direct tester binary patterns creation
-
Product
ADB Bearing Sensor Tester
-
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
Product
Scienlab Measurement And Control Module
SL1066B
Communications Module
The Measurement and Control Module SL1066B is a rack-mount measuring and control module that provides adjustable voltage outputs for BMS and DUT power supply and floating relay contacts to simulate e.g. vehicle specific terminals 15, 30 and 31.
-
Product
Mobile Test Systems
-
The systems include A+A+A+ LED solar simulators, high-resolution electroluminescence testers and various other tests that you can easily integrate into your transport of choice or directly into a container on site.
-
Product
Electronic Circuit Simulator
SimOne
-
SimOne lets you perform full-featured electronic circuit simulation using state-of-the-art and classic modeling algorithms while taking full advantage of modern computers.SimOne does all the basic circuit analyses common to SPICE modeling systems and as well provides important Stability analysis.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
ARINC 429 Test And Simulation PXI Module
PXI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
VI-CarRealTime
-
Vehicle dynamics and control engineers need a solution that optimizes vehicle and control system performance in a single vehicle model to accelerate the vehicle development process. That solution is VI-CarRealTime - a real-time vehicle simulation environment utilizing a single simplified vehicle model.
-
Product
GPS/GNSS Antenna Signal Splitter 2-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS221
-
INSTOCK Wireless Components, Inc
GPS221 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked port is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
LVDT/RVDT Simulation Board
75DL1
Simulator
The 75DL1 is a cPCI LVDT/RVDT Simulation Board that provides eight 2-wire or four 4-wire transformer isolated programmable outputs. It provides wrap-around self-test, PXI compatibility, optional Excitation Supply, and is available for Military or Commercial applications.
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
