-
Product
Double Voltage Double Frequency Generator Setup
DVDF
-
This test setup is generally used to perform induced voltage test on the transformers. This set up consists of the USED motor and generator combination to develop the required voltage and frequency. Both generating unit and the drive motor are mounted on a common metallic frame.
-
Product
High Voltage Power Supplies
-
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
Product
Water Cooled Laser Power Current Source
-
AMETEK Programmable Power, Inc.
Provides main power directly to the laser diode stacks.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
Programmable AC Power Source
LSP-500VAC
-
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Product
AC Voltage Test Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Voltage & Continuity Testers
-
Our range of CombiVolt voltage testers are designed to measure AC/DC voltages and continuity. Most models provide LED indication, an audible tone or a combination of both while others have a digital display to give an exact reading, all testers have a non RCD Trip feature
-
Product
Sund Source
Qohm
-
The extreme low weight of 3.5 kg and small dimensions allow highly efficient measurements, saving time in transportation and test-set-up. This set prevents heavy lifting work and allows flexibility in positioning during tests, because also the tripod, power amplifier, and soft-bag are light weight.
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
-
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
High-performance Impulsive Source
G-SOURCE II
-
G-SOURCE II is the most advanced impulsive source of its class, bringing high performance in the toughest conditions. Its compact size, easy adaptability and strong performance through a higher peak amplitude than any conventional impulsive source, make it perfect for any advanced marine seismic survey.
-
Product
Light source
UVM-MP
-
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
Product
AC/DC Withstand Voltage Test
WB2671A/WB2671B
-
• Output voltage: 0-5kV (AC/DC); • Cutoff current range: AC 0~20mA (WB2671A)/0~100mA (WB2671B); DC 0-20mA; • Test time: 1-60s; • Transformer capacity: 750VA.
-
Product
High Voltage Pulse
-
For thicker coatings such as coal tars, extruded and tape coatings, It has a range of infinite voltage settings from 1,000 to 15,000 volts. This wide range permits you to maintain a steady inspection rate on most types of coatings on most pipe sizes without changing detectors. Pulse voltage output only.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
OIP TYPE VOLTAGE TRANSFORMER
-
12kV - 145kV post type voltage transformers having Oil Impregnated Paper( OIP) as major insulation has been designed with several unique features.OIP insulated outdoor products are subjected to extreme climatic conditions and hence extra care is taken in the design and manufacturing of such transformers.
-
Product
PXIe CW Source, 1 MHz to 3 GHz or 6 GHz
M9380A
-
Save floor space with a compact, modular analog signal generator Provides Keysight quality and performance for local oscillator (LO) substitution, interference and component test Minimize need for external amplification with output power of +18 dBm across the frequency range Reduce test time with easy integration into your high-speed automated test system
-
Product
USB Voltage Measurement Bundle
-
The USB Voltage Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure input voltage signals while providing isolation and overcurrent protection for high-voltage applications.
-
Product
DC-DC High Voltage Power Supplies
-
DC inputs from 21.6 to 32.0 Vdc input may be used for these versatile power supplies. Although their outputs are continuously adjustable from 0 to their maximum ratings, 20-turn controls permit precise setability.
-
Product
Pulsed Laser and LED Light Sources
NanoLED
-
The NanoLED range is a novel and economical light source system that utilizes pulsed laser diode and LED technology to generate short optical pulses over a wide range of repetition rates and wavelengths. Optical pulses as short as 70ps can be generated at repetition rates up to 1MHz.
-
Product
Animal Temperature Controller - Low Voltage
TCAT-2LV
-
Our TCAT-2 family of general purpose PID Autotuning Controllers provides accurate temperature control in a variety of laboratory applications. Combined with a heat lamp or heating pad, the TCAT-2 may be used to maintain the body temperature of anesthetized animals during surgery or stereotaxic procedures. Small animal cages are easily warmed with a heat lamp. The TCAT-2 may also be used in cooling applications, such as to control independent perfusate cooling systems. Realizing that laboratory applications are diverse, Physitemp can provide several versions of the TCAT Controller. The model specified depends on whether a laboratory has a general or specific need for the controller
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
High Voltage Power Supplies
DR5 Series
-
The DR5 system comprises: DR5A host controller; and DR5V high-voltage chuck power supply with adaptive grip and release.
-
Product
Full Band (1200 ~ 1700 nm) Tunable Laser Source
CA9813
-
This specification describes and defines Advanced Lab Instruments CA9813 full band CW tunable lasers with applications to test and measurement equipment. It provides fast wavelength tuning, high power output, and high power stability. Advanced Lab Instruments tunable laser products support full-band, and other single-band operation. A full-band tunable laser is also available, covering 1200 ~1700 nm wavelength range, with seamless tuning.
-
Product
Calibration Light Sources
-
For wavelength calibration, Avantes offers a variety of sources including Argon, Mercury-Argon, Neon, Zinc, and Cadmium. All Avantes spectrometers are factory wavelength calibrated and do not require recalibration as they have fixed slits and optics. For those customers who wish to do their own calibrations, the AvaLight-CAL light sources can be used for recalibration purposes. For auto-calibration, AvaSoft-Fill provides a calibration procedure to make this easy.
-
Product
HV DC Voltage Generators
-
Fivestar HV Testing Equipment Co., Ltd.
HV DC voltage generators are used to generate high voltage DC test voltages for routine, type and development test on components and complete systems found in electrical power supply systems and operating on DC voltage (HV transmission systems etc). There are K and M series, and available for indoor and outdoor.
-
Product
LXI High Voltage Matrix 2-Pole 100x2
60-310-102
-
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing. The 60-310 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
Tunable CW Laser Source
IQTLS
-
The IQTLS is a continuous wave (CW) laser source combining high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability. Available in single or dual laser configurations, this tunable laser source can be controlled locally via USB or Ethernet ports and is SCPI VXI-11 compliant.
-
Product
LED Uniform Light Sources
-
Integrating sphere light source with LED illuminants (white, RGB-colored, NIR). Options available like variable output control and monitor detectors. We are experts in providing customer specific systems. Please contact us for all possible solutions and finding your perfect solutions. E.g. for EMVA 1288 Standard.
-
Product
Noise Source Generators
-
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
Product
Calibration Light Source
CAL2
-
Image Engineering GmbH & Co. KG
The CAL2, based on our 22 channel spectrally tunable iQ-LED source, can be adapted for use in many different areas.
