Simulation Software
computer programs that emulate the function of a system, predict expected performance, evaluate the impact, and assess design alternatives.
See Also: Simulation, Simulators, Simulation Testing, SPICE, Predictive Analysis
-
Product
Synchro Simulator
SPA-CASE
-
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
-
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
-
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
41-752A-103
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 4-Banks
43-670-101-AABBCC
-
The 41/43-670-101 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
-
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-911
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
-
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
STANAG3910 Test And Simulation Module – Rafale – For PCI Express
APEX3910-EN
-
Single Stream STANAG3910 Test and Simulation module – Rafale – for PCI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE). The APEX3910-EN is a functional replacement for APE3910-EN.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 350 Ohm
40-265-012
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 1k
50-265-202
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Load Simulator
-
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
PXI RTD Simulator Module, 4 Channel, PT100
40-263-501
-
The 40-263-501 is a 4-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X FC4 Simulyzer
-
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. With a simple firmware/software upgrade, a single function board can become a full function board without having to purchase new hardware.
-
Product
I-Pi SMARC Development Kit Based On NXP® I.MX 95 Six-Core Arm® Cortex-A55, M7 & M33
I-Pi SMARC IMX95
-
The ADLINK LEC-IMX95 is a powerful and versatile SMARC module that delivers high-performance computing, graphics, machine learning, and vision capabilities for IoT and industrial applications. It is based on the NXP i.MX95 processor, which integrates six Arm Cortex-A55 cores, one Arm Cortex-M7 core, one Arm Cortex-M33 core, an Arm Mali GPU, an ISP, and an eIQ Neutron NPU that can run at up to 2 TOPS.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
-
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
43-752A-102
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Photovoltaic Array Simulator
PV8900 Series
-
Keysight’s photovoltaic (PV) simulator includes the hardware and software to test a single maximum power point tracking (MPPT) inverter accurately. Test PV voltages up to 2000 V and 60 A with a single supply. DG9000 Series software licenses are available to test string inverter with 4-, 8-, or 12-MPPT channels. Most string inverter solutions test one MPPT channel at a time — leading to test inaccuracies. Keysight's DG9000 advanced PV inverter software can test up to 12 MPPT channels simultaneously.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
-
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Battery Simulator
1200
-
The Battery Simulator 1200 provides isolated channels to simulate battery sink and source characteristics often used for testing a Battery Management System (BMS). The instrument can be used standalone with the soft front panel, or integrated into a larger test system. Its proper industrial cooling and cell channel isolation allows units to be easily stacked, providing solutions with over 200 channels of simulation capability. The built-in channel voltage and current readback reduces the need for external monitoring equipment.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 3k
40-265-106
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
41-670-103-AABBCC
-
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
NVIDIA® Jetson Orin™ Nano Developer Kit
MIC-711D-ON
-
Open-frame carrier design with thermal solution. Embedded with NVIDIA® Jetson Orin™ Nano up to 67 TOPS. Supports 1 x GbE, 2 x USB 3.2 Gen 1 (5 Gbit/s). Supports 1 x mPCIe, 1 x M.2 3052, 1 x M.2 2280.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1K
40-265-202
-
The 40-265 is a strain gauge simulator that simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
3U VPX Development Kit
-
This development kit enables efficient 3U VPX backplane design and software verification.- 3U VPX architecture- One CPU blade, one GPU blade (optional), SOSA-aligned- 1TB NVMe pre-installed in CPU blade- Rear transition module(s) included- Test Frame with backplane pre-installed
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Portable Range Threat Simulators
-
The Textron System's PRTS™ and HPRTS™ are medium and long-range, programmable, ruggedized Radio Frequency (RF) test and training tools. Our PRTS family of range simulators delivers high-fidelity environments for training ranges.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 2K
40-265-302
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI RTD Simulator Module, 16 Channel, PT1000
40-263-203
-
The 40-263-203 is a 16-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
