Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
PHIL 4-Quadrant Power Amplifier
PAV5000
-
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
Product
Fiber Optic Sensors And Amplifiers
-
Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.
-
Product
Limiting Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-28Gbps) limiting amplifierExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the amplitude adjustment tuning portIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with adjustable SE amplitude from 0V to 1.0VSingle +3.3V or -3.3V power supplyPower consumption: 660mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Analog I/O module with 16 differential analog output channels
IO107
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
Differential Pressure Switches
P845
-
The Whitman Controls P845 Differential Pressure Switches are rugged and versatile, with excellent by-pass characteristics and the ability to handle a wide variety of media to 6,000 PSIG and set point ranges to 250 PSID. These switches are NEMA 4 rated and can tolerate submersion. They are commonly used across oil and water filter heads to detect when a filter element needs changing. It may be mounted in any orientation and is capable of carrying light to moderate mechanical shock and vibratory loads.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Replacement Alligator Clips for High Voltage Differential Probe
PK-HVA-01
-
Replacement Alligator Clips for High Voltage Differential Probe
-
Product
Differential Interferometer
10715A
Differential Interferometer
The Keysight 10715A Differential Interferometer performs differential measurements between the supplied reference mirror and a measurement plane mirror. It provides exceptional long term stability. The 10715A minimizes dead path, and, because the entire optical path through the interferometer is common mode, it eliminates thermal drift in measurements. The resolution of the measurement is twice that of a linear or single-beam interferometer.
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
-
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
Product
Differential Transformer Type Extensometers
DT Series
-
ISO Class 1 Compliant Differential Transformer Type Extensometers The ISO 6892-1 standard for tensile testing of metallic materials prescribes Class 1 or higher extensometers, and JIS Z2241 prescribes Class 2 or higher extensometers when measuring withstanding pressure. The DT series includes Class 1 compliant differential transformer type extensometers, which can be used to implement test methods compliant with metal tensile test standards.
-
Product
Measuring Amplifiers
-
Smart force measurement with a parameterizable measurement amplifier.
-
Product
16-bit, 400KHz, 4 Isolated Analog Differential Inputs, Simultaneous Sampling
APCI-3003
-
With the new fast A/D converter board APCI-3003, the user can achieve high data transfer rates by a simultaneous conversion of 4 channels at once. The board has 4 differential input channels. Each channel has its own A/D converter. The transfer rate can be set in a flexible way from 100 kHz for each channel, when 16 channels are set, to 400 kHz for each channel, when 4 channels are set. All 4 channels are optically separated from each other up to 500 V.
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Amplifier Modules
RF Amplifiers
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project.
-
Product
Linear High Efficiency Power Amplifier
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's high efficiency linear power amplifiers are available for operating frequencies from 1MHz to1 GHz with output power from 1 to 100 watts. Combined with linear design, these linear power amplifiers provide ultra low distortion, suitable for multi-band, multi-mode communication applications. With built-in monitor circuits, Keylink's power amplifier assure consistent performance in terms of reliability. KeyLink's linear power amplifiers can be categorized as follows:
-
Product
Semiconductor Power Amplifiers : Solid State Power Amplifiers (SSPA) For Indoor (rack-mount) And Outdoor (hub-mount) Settings
-
Insight Product Company is proud to offer state-of-the-art semiconductor (solid state) power amplifiers that are compact, rugged, and deliver immense power, and expectional frequency stability and minimal phase noise. These solid state power amplifiers are ideal for indoor, rack-mount, or outdoor, hub-mount, applications. We offer S-band, C-band, X-band, and Ku-band amplifiers, with output power of upto 1,000 Watts (varies based on frequency band).
-
Product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Differential Manometer
EM152
-
UEi Test & Measurement Instruments
Dual input manometer with easy-to-read display, intuitive interface and built-in magnet makes this manometer convenient to use
-
Product
Differential Pressure Flow Meters
-
Engineers can rely on the V-Cone dp flow meter to make life easier. McCrometer’s differential pressure flow meter is the versatile, highly compatible flow measurement solution for a variety of industries. When accuracy and repeatability are critical, the V-Cone’s performance brings superior value.
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
High-Voltage Differential Probe, 25 MHz
N2791A
High Current Probe
Use the N2791A 25-MHz low-cost high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2791A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 700 V of differential voltage and common mode voltage.
-
Product
OEM Femtosecond/Picosecond Laser and Amplifier Modules
-
They provide output wavelength options at 780 nm, 925 nm, 1030 nm, 1064 nm and 1550 nm and can be used as stand-alone systems with a user-provided 5 V DC power supply or integrated into higher power laser platforms. The high quality ultrafast pulse streams are perfect seed sources for chirped pulse amplifier systems used in diverse applications, such as high precision microelectronics micromachining, laser eye surgery and nonlinear spectroscopy.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
CAN Interface
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
