-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5891
-
- Simultaneous synthesis of up to 10 different clocks- 16 SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Eight programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Module 6x24 Bit, 0 Ohm to 16M Ohm
40-295-121-6/24
Programmable Resistor Module
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Small Form Factor Digital I/O Modules
-
Diamond's Digital I/O module family includes a wide range of rugged, wide-temperature PC/104, PC/104-Plus, PCIe MiniCard, and FeaturePak modules featuring programmable bi-directional digital I/O, counter/timers, optoisolated inputs, and relay outputs.
-
Product
Pulse Laser
-
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5962-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PXI High Voltage Programmable Resistor Module, 2-Channel, 4Ω To 770kΩ, D-Type Connector
40-230-043-HI
Programmable Resistor Module
The 40-230-043-HI (PXI) and 42-230-043-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 770kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-045
Precision Resistor Module
The 40-297A-045 (PXI) and the 42-297A-045 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Emulates Winbond W78ERD2
FE-WRD2
-
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W
T3PS160141P
DC Power Supply
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-131-HI
Programmable Resistor Module
The 40-230-131-HI (PXI) and 42-230-131-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High-Power DC Power Supplies
N8900 Series
-
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW auto ranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' auto ranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R with SPDT
40-293-111
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-032
Programmable Resistor Module
The 40-254-032 (PXI) and 42-254-032 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm
50-293-033
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel, 1 Ω to 61 Ω
40-297A-111
Programmable Resistor Module
The 40-297A-111 (PXI) and the 42-297A-111 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 61 Ω, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
High Power Programmable AC Source
-
Chroma Systems Solutions, Inc.
Simulate various AC line input conditions and measurement of critical characteristics for products under test
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.596-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-352-HI
Programmable Resistor Module
The 40-230-352-HI (PXI) and 42-230-352-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-113
Programmable Resistor Module
The 40-254-113 (PXI) and 42-254-113 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 238Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Frequency and Phase Agile 120 MHz Signal Generator.
DDS8p
-
The DDS8p generates cosine, sine and ACMOS/TTL output signals. The frequency is programmable in 1µHz steps from 100Hz to 120MHz. The phase is 14-bit programmable. The DDS8p is controlled by a binary parallel interface that allows frequency and phase changes as fast as 600 nanoseconds. It is accurate to 1ppm and requires 5 VDC power.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 6.97kΩ
50-298-030
Programmable Resistor Module
The 50-298-030 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 122Ω
40-252-012
Programmable Resistor Module
The 40-252-012 is a programmable resistor module with 4 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7730-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
5 Gb/s Programmable Digital Delay Line
PDDL5
-
The PDDL5 is a precision time delay generator for digital signals. Delays are controlled precisely in 5, 10 or 20 ps increments from 0 to 5115, 10,230 or 20,460 ps range respectively. Data rates up to 5 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
Programmable Resistor Module
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
Load Module
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
