-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Electrodynamic Vibration Generator System
LVD-100KG
-
• Vibration table size: 500*500mm (Other size can be designed) • Vibration: 0~5mm (Adjustable range P-P). Vibration waveform: sine wave (half wave and full wave). Acceleration speed: 0~20g (Adjustable) • Maximum test load Capacity: 100kg • Accuracy: Frequency can be displayed to 0.01 Hz. Precision 0.1 Hz. • Sweep Frequency function (1~600Hz): (Upper frequency, Lower frequency, Time range) It can set real standard arbitrarily to sweep frequency back and forth • Programmable Function (1~600Hz): It can set each segment in 15 segments arbitrarily (frequency/amplitude/time/acceleration), and it can be recycled • Frequency doubling function (1~600Hz): 15 segments multiplied-increase: 1)Low to high frequency 2)High to low frequency 3)Low to high and then to low frequency, it can be recycled • Logarithmic function (1~600Hz), 3 modes of logarithm/can be recycled: 1)Lower to upper frequency 2)Upper to lower frequency 3)Lower to upper and then to lower frequency • Measuring instrument: To display amplitude, acceleration speed and the maximum acceleration speed.
-
Product
Differential Pressure and Temperature Data Logger
PRTemp1000D
-
The PRTemp1000D is a rugged pressure and temperature data logger designed to accurately monitor and record pressure and temperature at user programmable reading intervals. The rugged stainless steel design allows for the device to be placed in harsh environments, which makes it well suited for use with air conditioning systems, chilled water, hot water, air, gas, oil and steam pressure systems.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-041-HI
-
The 40-230-041-HI (PXI) and 42-230-041-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Digital Panel Meters And Modules
-
Measuring Method TRMS using Microcontroller1A / 5A Input in same Meter (User Selectable)High Accuracy Accros the Entire Range9999 Count High Resolution DisplayDual Aux. 110 V AC and 230 V AC in same MeterUser Programmable Display / CTR / PTRAuto Selection of Decimal PointAuto Indication of KV & KASetup / Programmable Protected by Password
-
Product
Programmable Step Attenuator, DC to 50 GHz, 0 to 65 dB, 5 dB steps
84908M
-
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-112-HI
-
The 40-230-112-HI (PXI) and 42-230-112-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe-5172 PXI Oscilloscope, 100 MHz, 14 bits, 250 MS/s, 8 Channels, 1.5 GB, FPGA: Kintex-7 410T
784226-01
-
PXIe, 100 MHz, 4- or 8-Channel, 14-Bit, Kintex-7 325T or 410T FPGA Reconfigurable PXI Oscilloscope—The PXIe 5172 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling and voltage range. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 250 MS/s or 100 MHz of analog bandwidth and advanced PXI synchronization. The PXIe 5172 also features a programmable Kintex-7 325T or 410T FPGA that can be used for custom acquisition, triggering, signal processing, and data streaming.
-
Product
PXI Programmable Resistor Module 3x24 Bit, 0 Ohm to 16M Ohm
40-295-021-3/24
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
PXI Power Supplies
-
Dual programmable power supplies are capable of supplying up to 60 Watts of power. These are ideal solution for applications where a self contained test system with a high power supply power capability is required in a PXI format.
-
Product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 22.3MΩ
50-298-154
-
The 50-298-154 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-312-HI
-
The 40-230-312-HI (PXI) and 42-230-312-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High-speed USB DAQ System
Model DI-4208
-
USB Data Acquisition (DAQ) System. Eight armored analog differential inputs*. Programmable range per channel: ±2, 5, 10, 20, 50 100 V full scale. Up to 120 V rms without damage. 50 dB common mode rejection. Supports ChannelStretch™ multi-unit synchronization*. Adaptable low-pass filter per channel. Corner frequency set as a function of sampling rate. 16-bit analog-to-digital resolution. 160 kHz analog sample throughput rate. Seven digital ports*. Programmable per port as input or switch. Support for rate measurements to 50 kHz. Support for 16-bit counter.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 102kΩ
40-298-134
-
The 40-298-134 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Digital Fluxgate Magnetometer
WFG-D-130
-
Output 3 axis fluxgate magnetometer to be commercially available. The Digital Fluxgate Magnetometer system can convert and transmit over its serial port (at 38400 baud) all three axes outputs at a rate of 250 samples per second. Slower data rates can also be selected; transmission rate and baud rates are user programmable.
-
-
Product
Multi-Channel 12-Bit, 5 GSPS Digitizer
ADQ36
-
ADQ36 offers software-selectable two- or four-channel configuration with 5 or 2.5 GSPS sampling rates respectively. The programmable DC-offset makes it ideal for sampling unipolar signals.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-113
-
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
User Programmable Logic
PCIe-Spartan-VI
-
User Programmable logic - Spartan VI 100 with 40 differential and 12 TTL IO plus PLL(24). 16 DMA ports, to support 8 full duplex byte lanes between the Bus and User FPGAs. Additional GPB interface to support R/W operations to registers etc. Driver and reference SW package includes user defined R/W to User FPGA to support User Architecture without a new driver.
-
Product
Ka-Band Silicon SATCOM Tx Quad Core IC
AWMF-0109
-
The AWMF-0109 is a highly integrated silicon quad core chip intended for satellite communications transmit applications. The device supports four dual polarization radiating elements with full programmable polarization flexibility. The device provides 22 dB of gain per channel with an output power of +12 dBm per element per polarization. Additional features include gain compensation over temperature, temperature reporting, and Tx output power telemetry. The chip features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-023
-
The 40-297A-023 (PXI) and the 42-297A-023 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Arbitrary Waveform Generator
-
An arbitrary waveform generator (ArbGen) is an extended function generator (FGen/FuncGen) that can generate freely programmable signals in addition to standard waveforms such as sine, square, triangle or trapezoid. In general, the voltage/current as well as the frequency/duration of the output signal can be freely adjusted.
-
Product
UltraZed PCIe Carrier Card for UltraZed-EG System-on-Module
AES-ZU-PCIECC-G
-
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™ compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches, LEDs, Xilinx SYSMON, and clock oscillator.
-
Product
Tachometers
TR5000
-
Features• Displays rate, time-in-process, ratio, sum, difference, or draw• Optional relay or 4-20 mA analog output• Completely field programmable• Full diagnostic functions• Setpoint and start delay functions• 3 programmable inputs• 3 programmable transistor setpoint outputs• Keypad lockout• 115, 230 VAC (50-60 Hz) and 10-30 VDC power options
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-152
-
The 40-297A-152 (PXI) and the 42-297A-152 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Benchtop LCR Meter
1692
-
The GenRad 1692 LCR Meter is a sophisticated, microprocessor-controlled tester that brings new levels of flexibility, simplicity and accuracy to RLC measurement. It's testing automation at its best with a range of programmable test frequencies and test voltages, as well as automatic limit comparison, automatic parameter selection, remote programmability, automatic binning and automatic zeroing. The display facilitates visual acquisition of test data and eliminates costly guesswork and errors. The 1692 LCR Meter provides a powerful combination of features designed to maximize productivity in production testing applications.
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k
40-293-024
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCIe Module
PCIe-1553-uAce-1,2
-
1or 2 controllers of dual redundant (A/B channel) 1553 communications• Programmable bus controller, remote terminal, or monitor terminal modes• MIL-STD-1553 A and B compliant, Notice 2 RT• STANAG 3838 bus compliant for NATO standard support• Long or short stub support • Low power consumption• PCIMG compliant• Single +5 VDC supply
