-
Product
In System Programmers
-
In-circuit serial programming, also known as in-system programming (ISP) or in-circuit programming (ICP) enables programming and reprogramming of microcontrollers, serial EEPROMs and flash memories already soldered on a target PCB.
-
Product
SparkFun Analog MEMS Microphone Breakout
SPH8878LR5H-1
-
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.
-
Product
ECU Interfaces
-
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
Product
Absolute Optical Inclinometer
A2T
-
The A2T is a single axis, digital gravity angle sensor. The A2T serves as a full 360 range absolute tilt sensing programmable level with either digital or analog output. Internally, a rotary bar coded disk is mounted to a weighted gravity driven wheel. A micro-controller strobes an LED to transfer the bar code image onto an optical linear array, then decodes the position every 2 mSec. Magnetic damping provides fast response and settling time while virtually eliminating overshoot and oscillations. An internal EEPROM stores field programmable parameters such as resolution, zero position, direction swap, and mode. This second generation design virtually eliminates the primary accuracy limitation of first generation inclinometers, which is sitation (hysteresis).
-
Product
Absolute Optical Encoder Kit Version
A2K
-
The A2K absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2K reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
Microcontrollers And Microprocessors
-
In response to user requirements that are rapidly expanding in scope, Renesas Electronics offers microcontroller and microprocessor products that provide excellent expandability while allowing customers to make full use of existing resources.
-
Product
Controllers
-
Applied Scientific Instrumentation
100 MHz Microcontroller for faster command processing and servo controlClosed-loop DC servo control of up to four motorized axesFirmware upgradeable via serial connection0-10V DAC for single piezo axis controlRemembers last position on power down/upLCD display shows axes coordinates and status“Zero” and “Home” buttons for simple stand-alone operationsUSB or RS232 serial control with baud rates to 115200 BaudCompact ergonomic tabletop control unit 6”D x 9”W x 3”H (16½ x 23 x 9 cm)
-
Product
SparkFun SAMD21 Development Board
Qwiic Micro
-
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
Product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/D1x (Automotive Only)
-
Renesas is introducing the RL78/D1x as an optimized solution for the BRICs and low-end instrument cluster markets. The RL78/D1x is the successor of 78K0/Dx2 or UPD78082x microcontrollers and suited for car instrument cluster, built-in car instrument cluster dedicated features such as Sound Generator, Stepper Motor Controller/Driver and LCD Segment Controller/Driver etc.
-
Product
Microcontrollers
-
32-bit Qorivva microcontrollers based on PowerArchitecturetm e200 cores, that can run up to 264MHz. These devices include flash and RAM memory, as well as a number of external interfaces making them suitable for Aerospace & Defense of applications.
-
Product
Low Cost Emulator
EB-51
-
# Emulates 80C51 Microcontrollers and Derivatives# Real-Time Operation up to 40 MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C, PLM and Assembler# DOS and MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 64K of Code and 64K of Data Memory# Data Memory with Mapping Capabilities# Performance Analyzer# Real-Time and Conditional Breakpoints
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Electricity Metering Device- Residential
ES-10B
-
Designed for the residential smart meter rollout in Great Britain, this 4 terminal single phase electricity meter is the second generation version within our SMETS2 compliant solution.Taking learnings from the first generation meter, the ES-10B is a more refined SMETS2 compliant electricity meter with 100A main disconnect relay, dedicated secure microcontroller and with multiple interfaces including Zigbee and DLMS.
-
Product
Gate Drivers
-
A necessary companion for discrete power MOSFETs and IGBTs as well as digital – microcontrollers, DSPs and FPGs – or analog controllers in any switched-mode power converter, STDRIVE gate drivers generate the necessary voltage and current level required to accurately and efficiently activate the power stage in industrial, consumer, computer and automotive applications.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
RH850 Family (Automotive Only)
-
The RH850 is Renesas Electronics' latest automotive micro-controller family that offers high performance balanced with very low power consumption over a wide and scalable range of products. This family offers rich functional safety and embedded security features needed for new and advanced automotive applications.
-
Product
32-bit Microcontrollers (MCUs)
EFM32™
-
The energy-friendly EFM32 MCUs are ideal for ultra-low power applications. Based on ARM Cortex-M0+, Cortex-M3 and Cortex-M4 cores, EFM32 MCUs also include the most energy-friendly peripherals and energy modes to enable design of highly functional low power systems.
-
Product
Code Optimizing C Compilers for Microchip PIC® and dsPIC® DSCs
-
CCS developed the first C Compiler for Microchip microcontrollers over 20 years ago and continues to provide software solutions to developers of embedded applications using PIC® MCU and PIC24/dsPIC® DSC devices. CCS compilers are easy to use and quick to learn. For the less experienced programmer, a detailed textbook explaining the C language and how it may be applied to PIC® microcontrollers.
-
Product
Sunshine Duration Sensor
SD4
-
Four identical omni-directional sensors under a hemispherical shading canopy. Embedded microcontroller executes a sophisticated contrast-evaluation algorithm to accurately discriminate direct sunshine from diffuse sunlight.
-
Product
Development Platform
LaunchPad™
-
Begin rapid prototyping applications in minutes with our microcontroller-based LaunchPad kits, Sitara™-processor-powered BeagleBoards and SimpleLink™ wireless connectivity SensorTags. The Sidekick line of kits from Seeedstudio offer customers a quick way to evaluate custom circuits with many of the popular microcontroller development kits available on the market.
-
Product
Orange5 Programmer
-
Orange 5 is a professional tool for programming memory and microcontroller. A unique feature of the current generation of programmers is built macrolanguage the preparation of records. It enables the addition of new types of micro patterns, meeting the requirements of manufacturers’ read and write algorithms
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
FCB Probe Card
-
The FCB Probe Card is the most mature technology of buckling beam probe card. It is aimed to achieve the semiconductor ship manufacture time-to-market (TTM) and cost of test (COT) demand. FCB is a proven solution for a variety of semiconductor production tests from early engineering pilot-runs to high volume manufacturing (HVM). FCB is ready for device requiring high signal integrity probing (SI) and/or power integrity probing (PI). Applications include cutting-edge SiPs/SoCs, WLP, graphic processors, micro processor, industrial microcontrollers, and more. FCB guarantees the world’s best overall cost-of-ownership (COO) for various DUT applications.
-
Product
SparkFun Qwiic Scale
NAU7802
-
The SparkFun Qwiic Scale is a small breakout board for the NAU7802 that allows you to easily read load cells to accurately measure the weight of an object. By connecting the board to your microcontroller you will be able to read the changes in the resistance of a load cell and, with some calibration, you'll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control or simple presence detection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
TMR Gear Sensor Demo
-
MultiDimension Technology Co.,Ltd.
The Gear Demonstration Board is a complete gear sensor system with microcontroller, graphic LCD display and incremental A/B output indication LED which demonstrates the capabilities of MMG444DG devices. The absolute phase measurement provides instant indication of the gear’s angular position with a resolution of 1.4° = 256 positions per revolution and the absolute value of the teeth.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
ADXL345
-
Filling out our accelerometer offerings, we now have the really lovely digital ADXL345 from Analog Devices, a triple-axis accelerometer with digital I2C and SPI interface breakout. We added an on-board 3.3V regulator and logic-level shifting circuitry, making it a perfect choice for interfacing with any 3V or 5V microcontroller such as the Arduino.
-
Product
Renesas Synergy™ Microcontrollers
S1 Series - Low Power
-
Maximize battery life in portable sensor and control applications with the S1 Series, operating down to 1.6V with extreme low power modes and fast wake-up times. Optimize CPU bandwidth and reduce power consumption with integrated features such as hardware-accelerated peripherals, while a True Random Number Generator and AES provide secure connectivity.
-
Product
SMARC V2.0 SoM With I.MX8M Quad/Dual 1.5 GHz/1.3 GHz (Industrial) SoC, 4GB RAM, 64GB EMMC, CAN, MIPI CSI/DSI And HDMI 2.0
SCM180
-
The SCM180 is a SMARC v2.0 system on module with a choice of quad- or dual-core Arm® Cortex®-A53 processors. The ultra low power, high performance, RISC-based module measures only 82 x 50 mm and utilizes the powerful i.MX 8M processor. Its scalability, optimized pinout schematic and low profile design offers high level of versatility to help system integrators drive their important projects forward. The SCM180 is unique among other SMARC modules of its kind because it features Trusted Platform Module (TPM) for optimum security. With a discrete, dedicated microcontroller designed to support hardware encryption and decryption, the SCM180 delivers enhanced security for an added layer of protection. It also offers a choice of operating temperature ranges and can operate reliably in harsh environments. The SCM180 is suitable for a wide range of smart, portable/mobile-integrated IoT applications including robotics, automotive, factory automation, smart agriculture, casino gaming, medical, retail, surveillance and more. With its NXP artificial intelligence core technologies-enabled capabilities, the SMARC module can be programmed to support smart automation and machine-learning application requirements.
