In-circuit Test Systems
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-Circuit Test, In-circuit Testers
-
Product
Mezzanine System
5158
System
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Batterie Inspektor
Battery Test Platform
By combining the most diverse hardware and software modules, Batterie Inspektor™ delivers innovative, automated, and digitalized battery testing at every stage of manufacturing. With this flexible test platform, all modules can be adapted to their respective quality requirements. Manufacturing is simplified through a scalable and standardized framework for both new projects and upgrades.
-
Product
High-Performance Integrated Functional Test Platform
Spectrum-9100™
Test Platform
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
Product
Mezzanine System Carrier
MMS6245
System
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
VR/AR/MR Calibration Platform
Test Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
Universal In-Line Test Platform
Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
Product
Vision Systems
System
Embedded vision systems, also referred to as compact vision systems, offer an alternative to Smart cameras and computer-based systems. The ADLINK EOS series is a complete embedded system that offers image acquisition, processing, archiving, and display capabilities. It is equipped with a multi-core CPU, ideal for applications requiring high computing power and multi-camera imaging, such as 3D vision and robotics guidance. Featuring rich I/O connectivity with factory-floor networks, including RS-232/422/485, USB, and isolated digital I/O, as well as onboard storage, ADLINK’s embedded vision system is ready to deploy. A system monitoring feature, feeding back temperature and voltage data, combines with a watchdog timer to maximize robustness and reliability of the ADLINK EOS series in mission critical applications.
-
Product
Non-Signaling RF Test Platform for Validation & Production
Universal Wireless Tester
Test Platform
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
Product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
Functional Test
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
Modular Functional Testing Platform
OTP2
Test Platform
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
PCIe 2.0 Test Platform
PXP-100B
Test Platform
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
Product
Electronics Functional Test
Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
In-Circuit Testing and Test Engineering
GenRad 2287
-
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
-
Product
Test Handler
M6242
Test Handler
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Modular Breakout System 50-Pin D-type Plugin Module for 40-196
95-196-001
Modular Breakout System
The 95-196-001 Plugin Breakout Module is designed to be fitted to a PXI 40-196 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-192
95-192-001
Modular Breakout System
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
Battery Test Platform
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Data Acquisition and Control System
DAQ 7000
Data Acquisition System
data acquisition and control system that provides connectivity, signal conditioning and modular I/O for variety of sensors or signals, and it is an ideal DAQ for field deployment.
-
Product
Memory Test System
T5830/T5830ES
Test System
Highly flexible tester which has all of the capabilities needed to perform wafer sorting and final testing of price-sensitive flash memories
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Data Processing System
CRS-D8I-3VF1
System
The CRS-D8I-3VF1 VPX system’s I/O flexibility is capable of meeting a large number of configurations. It is designed to support Abaco Systems’ Intel 3rd generation Core i7 3U SBCs, Gigabit Ethernet switch, video compression card, CUDA-based graphics cards and a MIL-STD-1553/ARINC429 multi-protocol card.
-
Product
Functional Test for Engineering Lab
Spectrum BT
Functional Test
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
