Reactive Load Banks
Provide both lagging and leading power factor loads.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Resistive Load Banks
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2204HD-MS
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
PXI 4 Banks of 40 Channel 1 Pole MUX
40-615-022-4/40/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
PXI 2 Banks of 80 Channel 1 Pole MUX
40-615-022-2/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Digital Control DC Electronic Load
IT8200 Series
-
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
High Power DC Electronic Load
M97XX series
-
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
-
Product
Low Voltage Capacitor Banks
-
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
Product
Low Profile Universal Tension or Compression Load Cell
LPU SERIES
-
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
-
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
Product
High Precision Canister Load Cell
Model 2000 Series
-
The Model 2000 Series High Precision Canister Load Cell was designed to accurately and precisely measure force, which many other quantities such as torque, thrust, and pressure are based, for aerospace applications. The Model 2000 Series, available with load measurement capacities up to 750K lbf, offers high performance and linearity and very low hysteresis. ±0.02% FS Hysteresis
-
Product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
Product
PXI MUX 8 Banks of 8 Channel 2 Pole
40-610-022-8/8/2
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only)
510180101
SIM Insert
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only).
-
Product
Electronic Loads
SLM AC/DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
-
Product
Micro Power or Micro Coax, Insert, ITA, SIM, 2 Pos, 2 Slot (not loaded)
510181104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
PXI MUX 8 Banks of 16 Channel 1 Pole
40-610-022-8/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PXI 16 Bank 5 Channel 1 Pole Multiplexer
40-616-021-16/5/1
Multiplexer Module
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. The module is suitable for cascading in applications that require large multiplexer systems, it is also suitable for test systems that require the switching of a large number of signals in parallel.
-
-
Product
Bidirectional DC Power Supply + Regenerative Load
62000D
-
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Product
Receiver, I2 Micro ICon, 120/12 Position Hybrid, Loaded With Twin Female Contacts (610 138 200)
310130104
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 120 Signal QuadraPaddle contacts and 12 Micro Coax or Micro Power. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is pre-loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
Load Cells
-
We make it our business to stay on top of emerging industry demands so that the load cells we provide help you meet your ever-changing test requirements. Our broad selection of competitively priced load products will help you meet the most demanding test and measurement requirements. Used in automotive, aerospace and defense, R&D, and process control applications, our drop-in replacement load cells are designed to provide years of dependable performance.
-
Product
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)
510181110
SIM Insert
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 4 Ports
GPS402
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
Regenerative AC load function
61800 Series Optional Function
-
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
