PCI Express
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller. Also known as: PCIe
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, Serial ATA, Serial Peripheral Interface, SMBus, PCI Express Test, PCI Express Analyzers, PCIe
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Interface
RCNIC-A2PAU4
Interface
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Flexible Mini PCI Express to MiniPCI Adapter
SKU-066-0X
-
Flexible MiniPCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert motherboard MiniPCI Express bus into a standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard’s MiniPCI Express connector via full- or half-size MiniPCI Express host board.Adapter includes MiniPCI Adapter board, MiniPCI Express host board and flat PCI Express Cable.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
1100-Channel GSM Channelizer wih Quad A/D - 3U VPX
Model 52663
-
- Complete GSM channelizer with analog IF interface- Four 180 MHz 16-bit A/Ds- Two banks of 375 DDCs for upper GSM band- Two banks of 175 DDCs for lower GSM band- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express Gen. 2 x4- 3U VPX form factor provides a compact, rugged platform- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
4/8/12-ch PCI Express x4 Gen3 USB3 Vision Top Performing Frame Grabbers
PCIe-U300 Series
Frame Grabber
ADLINK's PCIe-U300 Series series is a PCI Express x4 Gen3 USB3 Vision frame grabber supporting 4/8/12 USB 3.1 Gen 1 ports for multiple USB3 Vision device connections with data transfer up to 5 Gb/s per port.
-
Product
USB ASSP
µPD720202
-
µPD720202 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides two USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
Product
PXIe-8399, Gen 3, x16, 2-Port PXI Remote Control Module
784180-01
MXI Express
PXIe, Gen 3, x16, 2-Port PXI Remote Control Module—The PXIe-8399 enables control of a PXI Express chassis from an external host, such as a desktop PC, rackmount controller, or a separate master chassis. Using a Gen 3 x16 PCI Express link, the PXIe-8399 provides up to 16 GB/s of data transfer between the chassis and host over a copper cable connection. An additional port allows daisy-chaining for multi-chassis configurations.
-
Product
5 Port PCI Express
PEX 8508
-
The ExpressLane™ PEX 8508 8-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device enables users to add low cost, scalable high bandwidth switching, both fan-in/out and peer-to-peer, to a wide variety of applications including office automation, network interface adapters, docking stations, AMC cards, and processor isolation for servers, storage, and communications.
-
Product
Circuit Module, Riser for ISMB 2U PCIe X16 Riser Card to 2 PCIx8 Expansion Slots , and PCI card
AIMB-RP3P8-12A1E
Circuit Module
Support ISG 2U chassis
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
SMARC
ROM-5780
-
Advantech ROM-5780 SMARC 2.1 Computer-on-Module is powered by Rockchip RK3399 SOC which includes dual-core Arm Cortex-A72 and quad-core Arm Cortex-A53 processors and Arm Mali-T860MP4 3D graphics engine. It provides rich display interface: HDMI 4K@60Hz, eDP and LVDS to meet different requirement. It also features USB3.0, PCIe 2.0, SATA, Gigabit Ethernet, MIPI-CSI for embedded applications. It is the ideal solution for POS, vending, infotainment, Medical.
-
Product
2-Ch 3.6 GHz or 4-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 6U VPX
Model 58841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with two 3.6 GHz, 12-bit A/D- Two-channel mode with four 1.8 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverter)- 10 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
WAN Adapters
FarSync K2Ee
-
The FarSync K2Ee PCIe card provides high performance 2 port low profile synchronous communications with multiple signalling modes for Linux and Windows systems.
-
Product
PCIe-7822, Kintex 7 325T FPGA, Digital Reconfigurable I/O Device
785360-01
Digital I/O Module
The PCIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - PCIe
Model 78751
-
Model 78751 is a member of the Onyx® family of high performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP. It includes two A/Ds, two D/As and four banks of memory. In addition to supporting PCI Express Gen. 3 as a native interface, the Model 78751 includes a general purpose connector for application-specific I/O.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
19” Rackmount Data Collection System
DCS-211
Data Acquisition System
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
Product
Pico-ITX SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, HDMI/LVDS And LAN
PICO312
-
The PICO312 is a palm-sized fanless pico-ITX motherboard built with the latest 14 nm Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake SoC). One 204-pin DDR3L-1867 SO-DIMM socket supports system memory up to 8GB. The tiny 2.5” pico-ITX embedded board features Intel® Gen9 graphics engine bringing a true high definition visual experience with dual display configurations through one LVDS and HDMI. In addition, it was designed for special needs of fanless operation under temperature from -20°C to +70°C. The PICO312 features a full-sized PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors with additional signals including one PCIe x1 lane, one LPC, one DDI, four USB 3.0 ports, one SMBus and one HD audio, giving this SBC high expandability to meet all requirements.
-
Product
PCI Express A/D Board
AD16-250 - Dual/Quad 16 bit, 250 MS/s
-
The AD16-250 series has two or four 250 MS/sec 16-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual and quad channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing up to four (4) times the effective memory depth.
-
Product
Carrier Card
SPR518
-
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
Product
6U VPX Computing Payload
VP62108
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62108 is a 6U VPX computing payload based on Intel® 4th generation Core™ Processor. It supports Intel® 4th generation Haswell architecture i3/i5/i7 dual-core or quad-core embedded processor, up to quad-core i7 processor 4860EQ with a life cycle of more than 7 years.VP62108 provides four serial RapidIO (SRIO) x4 links for VPX data plane communications, two x8 PCIe links for VPX expansion plane communications and four Gigabit Ethernet links for VPX control plane communications. Its rich data exchange capability allows users to easily build the whole machine or system-level solutions.VP62108 supports up to DDR3L 16GB ECC memory and offers reliable data transmission. Its onboard solid state Flash managed by a SATA interface controller can be up to 64GB SLC or 128GB MLC. And the entire board uses the reinforced conduction-cooled design and has a wide operating temperature, allowing the user not to worry about its working stability in harsh environments. This feature makes VP62108 particularly suitable for critical mission areas.
-
Product
BusTools/1553 BusTools Software Analyzer
-
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Six multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Advanced General Purpose FPGA
CertusPro-NX
-
*Up to 100K logic cells, 7.3 Mb of embedded memory blocks (EBR, LRAM), 156 18 x 18 multipliers, 299 programmable I/O, 8 SERDES supporting up to 10.3 Gbps per lane and supporting popular protocols (10 Gig Ethernet, PCIe Gen 3, DisplayPort, SLVS-EC and CoaXPress).*Packages as small as 9x9 mm, and in ball-pitch options of 0.5, 0.8 and 1.0 mm.*Power modes – User selectable Low Power vs. High Performance modes, enabled by FD-SOI programmable back-bias.*Design security – ECDSA bitstream authentication, coupled with robust AES-256 encryption.*Fast configuration – I/O configures in 4 ms, and full-device in under 30 ms in 100K LC device.
-
Product
Interposers and Probes
-
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 3U VPX
Model 52721
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- Three multiband DDCs- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential), up to 80 MS/s on 8 Channels (Single Ended)
M2P.5968-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - PCIe
Model 78610
-
Model 78610 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This digital I/O board provides 32 LVDS differential inputs or outputs plus LVDS clock, data valid, and data flow control on a front panel 80-pin connector. Its built-in datacapture and data generation feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
