Modulation Meters
Meters that measure the process, or result of the process, of varying a characteristic of a carrier, in accordance with an information-bearing signal. (atis.org)
See Also: Modulation, Optical Modulation, Modulation Analysis, Modulation Analyzers, MER
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 11-Bank 26.5GHz SMA
60-802-311
-
The 60-802-311 is a 4-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PCI Very High Density Multiplexer, 24-Channel, 4-Pole
50-670C-021-24/4
-
The 50-670C-021-24/4 is a 24-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Remote Mount, Failsafe
40-785C-472-TE
-
The 40-785C-472-TE (PXI) and 42-785C-472-TE (PXIe) are dual failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Isolated Common, Independent Isolation
40-651A-111
-
The 40-651A-111 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
PXI Solid State Multiplexer, 30 Amp, Dual 3-Channel
40-667A-011
-
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, LC Connectors
42-850A-414-M50
-
The 40/42-850A-414-M50 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI Monitored Multiplexer, Single 64-Channel, 1-Pole
40-619-301
-
The 40-619-301 is a high density PXI 2 A multiplexer module in single 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 1-Bank 40GHz SMA-2.9
60-801-401
-
The 60-801-401 is a 6-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI-2585, 10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module
778572-85
-
10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module —The PXI‑2585 is a high‐power PXI multiplexer switch module that is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779004-02
-
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
42-614D-006
-
The 40-614D-006 (PXI) and 42-614D-006 (PXIe) 4-bank, 32-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Breadboard Module for 34980A
34959A
-
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
PXI 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-614B-015
-
This 1-bank, 128-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Combination SPDT/Multiplexer Module
1260-37
-
The Astronics 1260-37 contains 40 Form C (SPDT) switches and eight 1x6 multiplexers. The multiplexers can be expanded using the on-board jumpers to four 1x12, two 1x24 or one 1x48 two-wire channel.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
-
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
FPD Tester Power Module
67393-120-480
-
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
Product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXIe-2524 , 128‐Channel, 2 A, Multibank, 1‐Wire PXI Multiplexer Switch Module
780587-24
-
128‐Channel, 2 A, Multibank, 1‐Wire PXI Multiplexer Switch Module —The PXIe‑2524 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in one of the following 1‑wire multiplexer configurations: 16 bank 8x1, octal 16x1, quad 32x1, dual 64x1, and 128x1. The PXIe‑2524 also features onboard relay counting for relay monitoring.
-
Product
PXI Remote Mount Triple SP6T Multiplexer 18GHz 50, SMA
40-785B-523-E
-
The 40-785B-523-E is a remote mount triple 6-channel 18GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-02
-
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
PXI Single Transfer Switch 18GHz 50Ω SMA
40-782-521
-
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 3-Bank 26.5GHz SMA
60-802-303
-
The 60-802-303 is a 4-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
COM Express Basic Size Type 6 Module with 6th Gen Intel® Core™, Xeon® and Celeron® Processors (formerly codename: Skylake)
Express-SL/SLE
-
The Express-SL/SLE is a COM Express® COM.0 R2.1 Basic Size Type 6 module supporting the 64-bit 6th Generation Intel® Core™ and Xeon® E3-and Celeron® processors (codename "Skylake-H") with IntelR QM170, HM170, CM236 Chipset.
-
Product
PXI Triple SP4T Multiplexer 6GHz 50 SMA
40-784A-103
-
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI/PXIe MEMS Optical MUX, Quad 2-Channel, Single-Mode
40-855A-342
-
The 40/42-855A-342 is a PXI/PXIe quad 2-channel multiplexer with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI Fault Insertion / Signal Insertion Switch Modules
-
Pickering's PXI Fault Insertion / Signal Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system. Two switching topologies are available: *Single signal paths with series switches and switches to connect to one or more fault buses*Pairs of signals with series switches, shorting switches between the signal pairs and switches to connect either signal to an external fault input.
-
Product
PXIe-2748, 3 GHz, 16x1 PXI RF Multiplexer Switch Module
780587-48
-
PXIe, 3 GHz, 16x1 PXI RF Multiplexer Switch Module—The PXIe‑2748 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 3 GHz in production test applications. The high channel count of the PXIe‑2748 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
Product
PXI Breadboard Module, 2-Slot, 15-Pin D-Type
40-220A-602
-
Versatile PXI Breadboard with 65 sq cm (10 sq in) of Prototype Area, fitted with 15-pin D-type connector, dual PXI slot width.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
779787-01
-
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 6GHz, 50Ω, SMA, Remote Mount
40-784B-101-E
-
The 40-784B-101-E (PXI) and 42-784B-101-E (PXIe) are single SP4T 6GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
