In-Circuit Test
Testing of short circuits, open circuits, component values and operation of ICs.
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-circuit Testers, In-circuit Test Systems, Combinational Testers, ICT
-
Product
EVSE Test Platform
Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
Modular Relay Board
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
Product
In-Line Test System
Test System
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
Product
Image Sensor Test System
IP750
Test System
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
Product
Test System Replication/Build-to-Print
Test System
Need to manufacture test stations? For more than 15 years we have sourced, assembled, tested and shipped fleets of robust, cost-effective solutions. We produce them at our high-volume facilities and deploy them around the world.
-
Product
LTE RRM Test System
T4010S
Test System
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
Test Platform
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
Test System
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
Product
VLSI Test System
3380
Test System
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Bottom Electrode SMD Test Fixture
16198A
Test Fixture
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
Product
SAS Protocol Test System
Sierra M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
In-Circuit Programmer/Loader
SKU-018-01
-
The In-Circuit Programmer/Loader (“EasyLoader” or “eLoader”) is a standalone device that was designed to provide a flexible and cost-effective solution for electronic device manufacturers, as well as for hardware design companies and their customers. It allows you to upgrade code on any JTAG/SPI/I2C compliant device (like FPGA/CPLD/EEprom/Flash, etc.) or Microcontrollers at any time of development, testing or production.
-
Product
Application Software for Electronic Test & Instrumentation
test
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Parallel Electrode SMD Test Fixture
16192A
Test Fixture
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
Audio and Acoustic Functional Test Solution
Functional Test
With the growing popularity of Internet of Things devices worldwide, many electrical products are adopting voice commands as their user interface. This means that acoustic and audio test challenges are likely to impact more products than ever before. Test teams must meet extended test coverage requirements to ensure product quality while maintaining throughput and operational efficiency. For a solution to meet these sorts of demands, it must:
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Active Alignment Assembly & Test Platform
Test Platform
Quickly deliver flawless camera & LiDAR modules, MEMS devices, die based sensors, LED and laser-based headlights and other high-end products with a supremely accurate standardized platform.
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
test
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
In-Circuit Tester
IP-5000, IP-5300
-
The IP-5000 series is a space-saving high-speed board inspection device with a compact design.
-
Product
Semiconductor Test Software
Test System
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
In-Circuit Emulator - 80C186/80C188 Family
DS-186
-
* Support for 80C186/8/XL/EA/EB/EC, 8086/8, V20/25/30/40/50 and other Microprocessors * Full-speed Emulation up to 25MHz * 1MB of Zero-Wait-State Mapped Memory * 8K x 32-bit Frames Dynamic Trace Buffer * 1MB Hardware Breakpoints * 115 KBaud RS-232 Communication Link * Numeric Coprocessor Support * OMF Converter * Support for Borland, Microsoft and Intel Compilers * Full Support for C, C++, Pascal and Assembler
-
Product
Magnetic Material Test Fixture
16454A
Test Fixture
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
Product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
System
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
Product
68HC16 In-Circuit Debugger
ICD16Z
-
P&E's ICD12Z for Windows is a powerful tool for debugging code. It uses the HC(S)12 processor's background debug mode (BDM), via one of P&E's hardware interfaces, to give the user access to all on-chip resources.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
