TTL
Transistor–transistor logic.
-
Product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
Digital I/O Module
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Ethernet to Relay Minibox™
Model 8064
-
* Model 8064-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.*Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 8064s.* Optional terminal board and terminal strip for easy connections without soldering. See the Ethernet Accessory page.
-
Product
Multifunctional Digital Design Core
PA72DIOS6016
Digital I/O Module
The PA72DIOS6016 is a multifunctional digital design core. The FPGA allows for implementing many different custom applications. The connector has 64 Input/Output pins which can be assigned as TTL I/O or as differential inputs. 128 MByte of DDR2 memory is available to the FPGA, and an onboard EEPROM allows for storing values in non-volatile memory. The I/O bank voltage can be FPGA-selected between 2.5 and 3.3 Volt.
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Digital Module
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
RS232 / RS485 / RS422 To Fiber Optic Converters
-
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
Product
Digital I.O Module with 64 TTL Channels
IO203
-
This I/O module is a dedicated digital I/O module providing a total of 64 TTL channels. The TTL transceivers are TTL and CMOS/TTL compatible and can also set to be CMOS compliant by the Setup driver block. Each of the 64 channels can individually be programmed as input or output. The 64 channels are further separated into two groups of 32 channels each.
-
Product
LCM Tester
Model 27011
-
To meet the high accuracy and low price requirements for LCM Test device, Chroma 27011 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL signal source fully complies with the digital signal standard, meanwhile with the 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight or LCM test without obtaining external power source.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
PCI Synthesizer
SYNTH300 Series
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Ethernet Digital Interfaces
-
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
Product
Random Access Monochromator
DeltaRAM X
-
The patented DeltaRAM™ X microscope Illuminator is the ideal fluorescence illuminator for quantitative intracellular ion research. It utilizes a galvanometer-based Random Access Monochromator (RAM) that can switch between any wavelength in 2 milliseconds. The DeltaRAM™ X is a complete, self-contained, illuminator that includes a power supply, high intensity xenon light source, DeltaRAM™ X monochromator, TTL shutter and flexible liquid light guide. The wavelength position is a simple analog voltage control. All you need to add is a microscope adapter for your fluorescence microscope and a USB or PCI DAC interface depending on the software you will be using to drive the illuminator.
-
Product
Full-Size PCI Express Mini Module With 32 Bit DIO
AX92904
-
*32 bit programmable DIO*Supports four 8-bit TTL level DIO ports with +5V powered*Each bit can be programmable as input or output*51 x 30 mm
-
Product
X Band Coupler With Dual Output Threshold Detector
-
The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
Function Generators
-
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad
-
Product
PCI Data Acquisition Boards
ADDA12-100DMA Series - Dual 12-bit A/D + Dual 14-bit D/A, 25 Ms/s
-
Model ADDA12-100DMA has two simultaneously sampling 12-bit A/D converters, two 14-bit D/A converters, five vectored TTL inputs and two vectored TTL outputs, and is able to transfer data directly into the computer system's memory at 100 MB/s in systems with 64-bit PCI slots or 80 MB/s in 32-bit slots.
-
Product
Ethernet Digital Interface
Model 8063
-
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* Transparent data transfer mode.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* 1 U high rack mount kit mounts one or two 8063s.* Includes 100-230 VAC Power Adapter with universal plugs.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784966-01
Controller
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
IC-3172, 1.80 GHz Intel Core i5 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784228-01
Controller
The IC‑3172 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3172 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
PCI-6503, 24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device
777690-01
Digital I/O Module
24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device - The PCI-6503 uses a 24-bit programmable peripheral interface (PPI). Each interface is Plug and Play compatible and does not require a separate card manager for configuration. The PCI-6503 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
-
Product
Programmable Logic Units
-
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/TTL (-40°C To +85°C)
SBC84620
-
The SBC84620 supports AMD LX800 500MHz processor and full feature I/Os. It is an ideal entry level PC-based embedded platform and be able to be fanless operation for industrial applications. The new integrated graphic controller, 4 COM, 4 USB 2.0 ports and 1GB DDR memory features empower the system value without extra development cost. In the meanwhile, for the expansion interface, the SBC84620 provides PCI with Mini PCI socket and ISA bus through PC/104 interfaces. Also, SBC84620 gives the best TCO (Total-Cost-of-Ownership) for system design due to DDR memory supported.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Multi Protocol Analyzer
LE-3500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
C Series Multifunction I/O Module
Multifunction I/O
The C Series Multifunction I/O Module is a cost-effective, general-purpose I/O module that helps system designers fit more functionality into a single system. The module includes analog input, analog output, and 5 V TTL digital I/O channels. You can use the C Series Multifunction I/O Module with select APIs such as LabVIEW FPGA.
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
