Magnetic Field
an force around magnets, electric current and atomic orbits.
See Also: Magnetic, Magnetic Test, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Magnetic Field Mapping, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test, Helmholtz Coils
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Magnetic Field Sensors
-
Analog Devices magnetic field sensors combine integrated bulk Hall cell technology and instrumentation circuitry to minimize temperature related drifts associated with silicon Hall cell characteristics. The architecture maximizes the advantages of a monolithic implementation while allowing sufficient versatility to meet varied application requirements with a minimum number of components.
-
Product
Magnetic-Field Test System
MTS-800
-
The MTS-800 is a compact test system for broadband generation and measurement of magnetic fields. Its internal components allow automatic EMC tests according to automotivestandards where high field strength need to be generatedor measured.
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
Complete Overview Of Magnetic Field Measuring Devices Teslameter Gaussmeter
-
The field strength measuring instruments are ideally suited for measuring magnetic field strength but also for residual magnetism (remanece)andetermination after demagnetization of metals.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1A
-
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Miniature Magnetic Field Sensor
FLC 100
-
Complete miniature fluxgate magnetometer can be used in any application where the sensitivity of Hall- or MR-magnetometers is not sufficient, e. g. measurement of the earth's field, detection of AC field from power lines, vehicle detection, compass navigation, and many others. Due to its low price and low power consumption ideally suited for multi-sensor array systems.
-
Product
Magnetic Field Press Device
-
Sometimes, magnetic application technology that can achieve results that push the limits of your products. Magnet-related equipment plays an important role in various fields such as electronics, metals, and physics.
-
Product
Magnetic Field Visualization
mageye
-
Our mobile "magnetic field sensor" allows you to visualize and evaluate magnetic stray fields. Our mageye, matesy’s miniaturized magneto-optical USB microscope, provides information about the magnetic fields on the surface of a wide variety of samples with resolutions in the micrometer range.
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
Magnetic Field Measurement Systems
-
The magnetic field probe performs non-contact current measurements and can be used for real traces. The probe of higher resolution enables pinpoint measurements.
-
Product
Magnetic Field Tester
MS-440
-
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
Product
Magnetic Field Generator
PFM61000-8A
-
PFM61000-8A Magnetic Field Generator is high reliability test equipment with stable performance, specially designed for electrical and electronic products for measuring immunity characteristics and requirements of normal frequency magnetic fields. It provides an accurate basis for the tested equipment in the immunity test of normal frequency magnetic field. The generator can imitate the magnetic field environments such as residential, commercial, industrial and mining enterprises, power plants, as well as middle and high substation. It fully meets IEC61000-4-8 and GB / T17626.8 standards.
-
Product
Triaxial ELF Magnetic Field Meter
SK-8301
-
Accurate measurement by- True RMS- Built-in XYZ triaxial sensorFor 40Hz to 1kHz magnetic field measurement.uT and mG are selectable.MAX/MIN and Average measurements.Compact and easy-to-carry.Easy operation by only 3-keys.
-
Product
Magnetic Field and Permeability Measurement
MAGNETOSCOP® 1.070
-
Foerster Instruments, Incorporated
The MAGNETOSCOP 1.070 is a portable magnetometer system with microprocessor and probes for measuring the magnetic flux density as an absolute or differential value (gradient). It has a USB port for simple data transfer and an SD card for saving measurement data and parameters. The measuring system also facilitates the recognition and saving of peak values and the adjustment of thresholds for limit values. The unit can be used for series and individual measurements. The data can be easily analyzed and documented with the PC software included in the scope of delivery. The MAGNETOSCOP 1.070 thus facilitates the portable and fast measurement of the relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys as well as the localization of ferrite enclosures. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
Product
Field Probe for Electric & Magnetic Field Measurement
WP400-3
-
Wavecontrol presents a new and unique field probe for the measurement of electric and magnetic fields that integrates both E & H sensors within dimensions of only 3 cm². Which makes it unique is that Wavecontrol has managed to add an E field sensor in a basic structure of a classical 3 cm² field probe. It has been possible, therefore, to obtain a 3 cm² field probe without compromising the capability of assessing E and H fields of its 100 cm² big sister, the recognized and successful WP400.
-
Product
Three Channel AC Magnetic Field Signal Conditioner
TCM-1A
-
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1
-
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Reference Magnet
-
Reference magnets generate a homogeneous magnetic field in an air gap. They are mainly used to calibrate hall probes for their full scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using reference magnets.
-
Product
Vector Field and Multi-Axis Systems
-
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
Product
Embedded Assembly Systems
-
EASY (Embedded Assembly SYstem) is the CAEN high/low voltage power supply solution every time residual magnetic fields and/or radiation become an issue.
-
Product
Magnetic Field Cancelling System
MK-1
-
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
Product
Split type Pulse Current Sensor
CTF-03
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Suitable for the operation and cable continuity check of the equipment by pulse current detection method. Wide AC current range from 0.1mA to 8A. Ultra compact and light weight. High sensitivity and least affection from external magnetic field.
-
Product
Hall Probes and Magnetic Pole Detector/Identifier
-
ChenYang Technologies GmbH & Co. KG
Is the new generation of the pole detector CY-PD248. It ispowered with one battery (1.5V, type AAA). The continuous operation time of the battery is longerthan 10 hours. The minimum detectable magnetic field is 9mT (90Gs).
-
Product
Primary Cable Fault Locating
Directional Impulse Detector
-
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
Product
Near Field Probes 30 MHz - 6 GHz
XF Family
-
The XF family consists of 4 passive magnetic field probes and 3 passive E field probes designed for measuring magnetic and E-fields in ranges from 30 MHz to 6 GHz during the development phase. Due to their integrated impendance matching the probes are less sensitive in the lower frequency range than the RF type probes.
-
Product
Measurements & Material Testing
-
MAGNET-PHYSIK Dr. Steingroever GmbH
, we can offer measurement tests and material tests of all kinds on hard and soft magnetic materials. It is also possible to carry out measurements on site. We carry out stray field measurements on your magnetization station in production in accordance with the professional association regulations (BGV). We also carry out magnetic field measurements on air freight goods in accordance with IATA 953.
-
Product
Electromagnetic
Promis 10
-
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
Product
Fully Automatic MRAM Probe System
-
*This system can measure MRAM characteristics automatically.*Generates strong and constant magnetic fields. (Max 1.5T, the highest in the industry)*Performs high speed sweep of magnetic field by using non-magnetic materials wafer chuck. (Max 4Hz, ±1T, the highest in the industry)
-
Product
Sensors
Magneto-Optical Sensors (MO Sensors)
-
The highly sensitive magneto-optical (MO) sensors form the basis for visualizing magnetic fields in production and research.
