-
Product
Capacitance & Tan-Delta Test System
TD-1
-
By measuring the electrical properties such as capacitance and Tan-Delta regularly on periodical basis, it is possible to ensure the operational unexpected breakdown. Dissipation factor (Tan Delta) is one of the most powerful off-line nondestructive diagnostic tool to monitor the condition of solid insulation of various high voltage equipment.
-
Product
C-Mic Testing System
BK3010
-
The BaKo BK3010 is our main C-Mic tester. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is so easy and intuitive, we based the BK3012 D-Mic Tester on it. It is also the model for our BK9010B Fully Automatic C-mic Tester.
-
Product
Lifecycle Test System
Model 933
-
The Model 933A Life Cycle Test System is a low cost, generic test platform used to perform cycling of keypads, keyboards, membranes, switches, or any product requiring fatigue testing.
-
Product
Systems Certification
-
Project integration offering a complete turnkey solution including design, engineering, FAA and international regulatory certification services and testing, and installation kit manufacturing.
-
Product
Stress Testing System
Load Dynamix
-
LoadDynamix (former Swifttest) is famous for its IP based converged storage system stress testing, including iSCSI, SMB/CIFS, NFS, FC and HTTP/HTTPS based storage systems. Its GUI interface is very easy to use and allow customer engineer to fully configure all the parameters at the protcol layer. Nearlly all the major IP storage system manufacturers have LoadDynamix products in their test lab.
-
Product
H+W (Pylon) 1280 Point Test System
-
H+W (Pylon) 1280 Point Test SystemUp to eight positions for 160 Point Wiring Blocks.
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
Product
Various Types of Automatic Hardness Testing System
-
Various Types of Automatic Hardness Testing System
-
Product
Power Supply Test System
-
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
Product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
-
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
Product
Mezzanine System
5181
-
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
Product
Battery Module (60v-300v) Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
The module test equipment adopts sinexcel advanced high frequency isolation scheme, and the detection process supports multi-gear switching. The equipment integrates voltage, temperature, pressure and other auxiliary channels, and can also integrate temperature box, water cooler and other equipment, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
Product
Brake Test Systems
GIANT Evo
-
The GIANT Evo is an extension of the well-proven GIANT product portfolio and has been developed to suit the growing demands and needs of the current and future brake markets. Covering the market segments from mini and compact cars to medium sized SUVs as well as large vehicles, this brake testing machine forms the base of HORIBA’s inertia brake dynamometers portfolio. All components are specifically tailored to the needs of the passenger car market segment.
-
Product
Test System
2000/DATS
-
WesTest Engineering Corporation
The WesTest-2000/DATS features Teradyne's high performance Digital Test Instrument and state-of-the-art intrsuments from Agilent, Elgar and North Atlantic.
-
Product
Flight Deck Power Systems
-
Multiple EmPower products are already a standard linefit option on Boeing and Airbus. Astronics flight deck power systems are modular in design and available in 110VAC, high power USB (10W), and the latest USB power delivery technology - USB Type-C (60W).
-
Product
Brake Hydraulic Pressure and Electric Parking Brake Systems Test Bench
Model BHP/EPB™
-
The new Model BHP/EPB™ Brake Hydraulic Pressure (BHP) and Electric Parking Brake (EPB) Systems test bench from MB Dynamics accurately measures and controls the hydraulic pressure and EPB power levels applied to brake calipers during automotive buzz, squeak and rattle (BSR) testing, as well as brake durability, stability, functional or performance testing. Varied brake pressures are applied according to timing diagrams, as well as automated or manually program-controlled repeat cycles, as required to assess brake caliper/rotor assembly noise, useful service life, and other critical performance metrics.
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Complete Systems
-
Your expert for measurement and automation tasks. For measurement and automation tasks that have special requirements, Delphin delivers complete systems with options and functions to enable optimal adaptation to any application.
-
Product
Vehicle Electromagnetic Field Test System
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are the daily means of transportation for our public, and the electromagnetic pollution in vehicles has received more and more attention from the public. The newly revised mandatory standard GB27630-201X "Air Quality Evaluation Standard for Passenger Cars" intends to require the electromagnetic field in the vehicle as one of the indicators. The measurement method measures the magnetic field strength in the vehicle. Within the frequency range of 10Hz-400kHz, the electromagnetic field measurement results should meet the requirements of the public limit of electromagnetic exposure in GB8702-2014.
-
Product
Monitoring Systems
-
Once a dynamic event is detected, the system instantly informs the control system or other external devices and acts as a digital recorder by capturing important data before and after the event. This information can be used to alert the operator to change process settings or schedule maintenance.
-
Product
Analysis System
Pegasus (EDS-EBSD)
-
The Pegasus Analysis System enables the simultaneous collection of Energy Dispersive Spectroscopy (EDS) (chemistry) and Electron Backscatter Diffraction (EBSD) (crystallography) data, allowing direct correlation between the elemental content and microstructural aspects of the material being studied.
-
Product
Portable System for High-Boltage Solid Dielectrics Testing
HVTS-70/50
-
Portable system HVTS-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
Product
Management System
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Monitors all systems from receiving sample to consumption, including coal truck, coal yard and equipment of sampling, sample preparation and analysis for fuel.
-
Product
Test System Elowerk
eloZ1
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
-
Product
MirrorLink Test System
Catena 2210
-
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
-
Product
Radar Systems
-
A radar system utilizing electronic-computer techniques whereby raw data is used to track an assigned target, compute target velocity, and predict its future position without interfering with the scanning rate.
-
Product
Die Test Handler
3112
-
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
Electrical Test System TY-CHECKER
Type E Series
-
High-speed, high-precision testers offered with a broad lineup, matching a range of test point numbers. Can be used alone and on our press systems.
-
-
Product
Battery Pack Test System
-
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
