Positioning
Aligning test set with target geography.
-
Product
Motors
-
When your application demands ultra-precise positioning and high throughput, trust Aerotech’s motor expertise.
-
Product
Bore Gauge
BG10
-
Aeronautical & General Instruments Ltd.
The BG10 Gun Barrel Bore Gauge System is an electro-mechanical measuring device that was originally introduced into service by the RAF for the high-speed measurement of aircraft cannons, to ensure minimum operational aircraft turnaround time. Measurements are taken at 16 pre-determined positions along each bore, which are then compared to pre-stored warning and rejection criteria. The actual measurements taken are displayed to the Operator on an LCD display and the measurements stored for future reference. The system will automatically provide a visual indication on the Hand Held Unit whether the barrel was acceptable, close to tolerance or rejected – all this to be undertaken in less than five minutes!
-
Product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
-
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
Product
VME
-
Highland Technology is a member of VITA, the VME standards body, and continues to release new technology into the VME market. As other bus architectures come and go, Highland remains confident that VME will maintain its position as the architecture of choice for essential, long life cycle programs.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
-
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 64 Position Module To TB-4300, 10V Input
540355010101
-
Cable Assembly, Receiver, TriPaddle, 20", 64 position module to TB-4300
-
Product
Satellite Signal Level Meter
Super Buddy 29
-
The Super Buddy 29 satellite meter has all of the great features of the standard Super Buddy satellite meter plus an internal combo 21 volt / 29 volt module to power the new DIRECTV SWM LNBs and the WildBlue / Telesat / Xplornet TRIAs! Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite.
-
Product
Extender
3690-3
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Temperature Sensors
-
Screw in positive mount installationGrease zerk for bearing lubrication1/2” NPT conduit entry (steel body)NTC version - continuous temperaturePTC version - trip points from 122°F to 194°FPT100 version - platinum RTDClass 2 Div 1, Div 2 Approved
-
Product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112772
-
Adapter Plate, 9050 Enclosure to 9025 ITA (ITA Positioned on Upper Part of L-Shaped Enclosure)
-
Product
PMC Carrier/Adapter/Motherboard
PMC-MC-X4-RIO
-
PMC-MC-X4-RIO adapter, carrier, motherboard provides the ability to install up to 4 (four) PMC modules into a small enclosure. PMC-MC-X4-RIO has two PMC card positions top and bottom to create a compact arrangement with 4 PMC positions. X4 is a complete solution with built in power supplies, thermal protection, voltage monitoring, bus arbitration, clock distribution, fan control and more. Compact chassis available to house PMC-MC-X4-RIO.
-
Product
Compact AC/DC Auto Ranging Clamp Meter
410002
-
The small bodies and jaws fit perfectly in your hand and into tight places. Meter controls are positioned so that current measurements can be done with one hand. A large backlit display is easy to see, and the handy display hold function keeps measurements fixed on the display. Measures starting current for motors, lighting, etc.
-
Product
2-28 Vrms Input, 2-115 Vrms Exc, 47 Hz - 1 kHz Freq
SDx
-
Synchros and Resolvers are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Resolver-to-Digital or a Synchro-to-Digital converter is used to convert these signals to a digital output corresponding to the shaft angle and/or velocity.
-
Product
Angle Position Indicator, High Accuracy
8810A
-
NAI's 8810A Angle Position Indicator (API) is a rack-mount or bench-top measurement instrument featuring front panel controls and input terminals. The use of an intelligent DSP design eliminates push buttons and allows all programming to be done either via an integrated touch-screen, front panel USB optical mouse interface, or with the multipurpose increment/setup knob. Improved flexibility is provided by two fully independent inputs that can be used to read two separate input signals simultaneously, or can be combined to measure multi-speed Synchros or Resolvers.Read more: http://www.naii.com/Angle-Position-Indicator-High-Accuracy/P196#ixzz3ztgONPA5
-
Product
Ascom IP-DECT
-
Ascom IP-DECT combines Voice over IP with Digitally Enhanced Cordless Telephony (DECT) technology. Ascom IP-DECT a reliable wireless communication solution that offers enterprise-grade telephony, professional messaging, personal alarm, and positioning over secure dedicated frequency bands. It is developed based on open standards, such as SIP, which maximizes interoperability with leading vendors.
-
Product
8-Channel VME LVDT/RVDT Scanner
V550
-
The V550 is a 6U, one-slot VME module which will acquire position data from up to eight LVDT (linear variable differential transformer) position sensors. The LVDT sensors are excited by an ultrastable synthesized sinewave generator, and conditioned by a precision 16-bit A/D converter followed by digital signal processing. The resident microprocessor supervises scanning and signal conditioning, and places updated position data in VME-accessible dual-ported data registers for instant access from the VME bus.
-
Product
NFC Conformance Test System
T3111S
-
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
High Precision Angular Positioning Calibration and Geometry Inspection
LabStandard
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.Designed for horizontal and vertical applications with self-locking worm gearing and a high accuracy angular encoder ensures sensitivity and fine positioning for metrology and precision testing.
-
Product
IO-Link Position Sensors
-
*Capacitive sensors for position detection or level monitoring*Distance sensors with very long range and background suppression*Ultrasonic sensors for non-contact detection of objects*Photoelectric sensors for specific applications*With switching output, analog signal and IO-Link
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
10-CH Pneumatics CAN
YAV90PNE
-
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
Product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
-
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Length Gauges
-
HEIDENHAIN length gauges deliver high accuracy, even over large measuring ranges. They are commonly used wherever fast, reliable, and accurate measurements are required, such as in production metrology, multi-gauging fixtures, measuring equipment monitoring, and position measurement.
-
Product
Position / Distance / Proximity Sensors
-
Panasonic Industrial Devices Sales Company of America
Easy-to-use Inductive Proximity Sensors provide stable detection for automation, with Sensors for standard to high speed, high performance solutions. These Inductive Proximity Sensors detect the presence and position of ferrous and non-ferrous metal objects and come in a range of IP Ratings (IP50 / 67 / 68 / 68g). The IP68g enclosure allows usage in very harsh environments. For high speed, high accuracy measurement, Laser Measurement Sensors are ideal for the precise measurement of thickness, diameter and height. Panasonic’s HG-C Series CMOS Type Micro Laser Distance Sensors deliver high repeatability for measurement distances (center) of 30mm, 50mm, 100mm, 200mm and 400mm. Ideal to measure insertion depths or thickness, these Sensors can also be used to detect warping, overlaps and presence helpful for preventative maintenance and remote monitoring. Select models are IO-Link compatible for ease of use.
-
Product
0.25° Accuracy Full Attitude Dynamic Motion Sensor
DMS-25
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Modul
782615-01
-
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at … the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
Product
Machine Vision for Robot Guidance
-
Machine Vision for robot guidance is the automation of automation technology. Speed, flexibility, and a high degree of positioning accuracy - all increase efficiency and reduce costs for tasks involving handling and processing. The experience of hundreds of applications in 2D and 3D robot guidance in various industries have poured into the design of the robot vision VIVA application package, allowing you to implement your application.
-
Product
H+W (Pylon) 1280 Point Test Interface
-
H+W (Pylon) 1280 Point Test SystemUp to eight positions for 160 Point Wiring Blocks.
-
Product
Automated Total Nitrosamine Analyser
-
Ellutia Chromatography Solutions
Nitrosamines are carcinogenic compounds that can be found and formed in many products. This has been a particular issue in the pharmaceutical industry recently. Traditional approaches to the analysis, such as by mass spec, have been challenging due to the low detection levels required, the possibility of false positives, or even missing. This system takes a unique approach of using the combination of a chemical reaction targeting nitrosamine compounds, then detection by a detector with very high selectivity and sensitivity for nitro/nitroso compounds. Rather than speciating the various nitrosamines present, the system gives a single quantitative result down to 1 ppb for the total nitrosamine content. This means both volatile and non-volatile nitrosamines are measured at the same time. This process is automated to allow a high sample throughput. This makes it ideal for screening a large number of samples rapidly.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, To PCB-Mounted 6x32-Pin Ribbon Cable Headers
510150155
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 6x32-Pin Ribbon Cable Headers
