Primary Current Injection Test
-
Product
Current Dataloggers
-
With our selection of current data loggers, you can meet requirements that include the single/split phase, three-phase, neutral, ground current and machine load monitoring. You can also utilize our current loggers for fault current detection, leak identification, and load profiling. We have compact models constructed to be weatherproof. Choose from stand-alone, handheld and clamp-on configurations. Our current data loggers are used in a broad scope of applications, trusted by technicians, electricians and engineers.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Precision Current Preamplifier
SIM918
-
Stanford Research Systems, Inc.
The SIM918 Current Preamplifier is ideal in applications in which the input offset voltage must be kept to a minimum. The DC voltage difference between the two inputs (current input and voltage bias) is accurately measured every 2 seconds, and is nulled.
-
Product
High Voltage Probes To Measure Primary Waveforms With A Power Analyzer
Volt Litewire
-
The Litewire is a true RMS meter designed for use by electric utilities to sense currents or voltage waveforms from the primary side of their distribution networks.
-
Product
Direct Liquid Injection System
VC Series
-
The VC Series is able to rapidly vaporize pure water or other liquid sources without carrier gas, which enables you to construct a more compact vaporization system.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
-
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
Current Probe
PA-629
-
*Maximum Current Value: +/- 200ADC, 140A RMS*1mA = 10mA, 100mA (switchable)*Rising Time: 1.2uS*Bandwidth: DC ~ 300kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
-
Product
Basic Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly.
-
Product
High Current Connectors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s offering includes various High Current Board-to-Board Connectors suitable for applications that require a connection to a power source/battery. These High Current Connectors have low mated height profiles, high reliability, and are manufactured with Panasonic's Tough Contact technology.
-
Product
Current Probe
-
Beijing GFUVE Electronics Co.,Ltd.
Used to measure control currents for relays in electronic circuits and in evaluation testing of capacitors' current characteristics.
-
Product
Current Measurement Board
MS 1814
-
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
Eddy Current Testing
-
Zetec is the industry leader for cost-effective eddy current testing in complex applications. We have the most extensive experience, and we develop the highest quality ECT inspection products. When it comes to understanding your needs, we’re your trusted advisor. And from instrumentation to probes to software, you can count on us to provide a complete inspection solution that will help you realize a cost savings in the long run. etec Eddy Current technology and products provide a fast efficient solution for near surface anomalies in conductive material
-
Product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
Leakage Current Testers
-
For general-use electrical devices Built-in non-medical use networks For rated currents of up to 20A For automatic testing on production lines, etc.
-
Product
AC Current Transducer
iDVM 333
-
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
Product
Auxiliary Current Transformers
-
Osborne Auxiliary Current Transformers are often used to reduce system currents to lower values appropriate for instrumentation and/or protection circuits. The Aux CT’s are designed for specific current ratios and burden impedance with a known transformation error. Osborne’s units are built for high performance and longevity in the most demanding environments.
-
Product
Current Transformer
CT
-
The split-core current transformers are easily installed with the snap on design.
-
Product
Primary Test Equipment
LET-400-RDC
-
The LET-400-RDC is designed to perform most of the primary tests that are necessary in substations commissioning. It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Fault Injection and White-Box Testing
VectorCAST/Probe
-
VectorCAST/Probe is integrated with the full family of VectorCAST tools allowing probes to be inserted during Unit, Integration, or System Testing. The probe insertions are controlled by the same technology that controls our code coverage instrumentation, which ensures that the probes function correctly regardless of the compiler, target processor, or run-time environment.
-
Product
Automatic Current Tester
77069
-
For the rapid safe and accurate testing of DC current on 12v vehicles. The tool plugs straight into the vehicles fuse board and displays the current on the large LCD display. Specification range 0-48volt max 20 amps, 12v battery included.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
AC / DC Current Probe, 100 KHz, 100 A
1146B
-
The Keysight 1146B AC / DC probe provides accurate display and measurement of currents up to 100 A DC or peak AC / DC to 100 kHz without breaking the circuit. The 1146B AC / DC probe has hall-effect sensor technology to measure AC and DC signals. It is compatible with any Keysight oscilloscope with 0.2 to 0.5 V / div sensitivity and 1 MΩ BNC input.
-
Product
Current Probe
DCFlex
-
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
Product
Automated Aerospace and Defense Test
-
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
6TL19 Off-Line Base Test Platform
H71001900
-
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
