Power Line
overhead or buried cable carrying electric power.
-
Product
Intelligent Power Monitor
iPM
-
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
Group Pulse Generator
STT-EFT-5K series
-
Beijing KeHuan Century EMC Technology Co,.LTD
STT-EFT-5K series group pulse generator is designed to determine a common and reproducible basis for evaluating the performance of electrical and electronic product power lines, signal lines or control lines when subjected to electrical fast transient pulse group interference. The performance of the generator meets the requirements of IEC 61000-4-4 and GB/T 17626.4 standards. Application areas: industrial control, home appliances, medical electronics, communication electronics, components, automation control, etc...
-
Product
Solid State Input Output Modules
-
Omega carries a wide variety of solid state input/output relay modules that provide dependable connections between power lines and computer interface systems.
-
Product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
-
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
HID Ballast Tester
WT2000-HID
-
• Input Parameters Measurement: 1) Test voltage, current, power, power factor, power line frequency, total harmonic and 0~50 harmonic 2) Range of voltage and current basic wave frequency: 45Hz~65Hz 3) Range of narrow frequency: 45Hz~5kHz 4) Range of wide frequency: 45Hz~1MHz
-
Product
Three-Pole Lighting And Surge Arrestor
PIVM12,5-275/3+0 Vseries
-
PIVM12,5-275/3+0 Vseries is a three-pole lightning and surge arrester Type 1+2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of both, the lightning current and the switching surge, which are generated in power supply systems entering the building. The use of the lightning current arresters PIVM12,5-275/3+0 Vseries is mainly in the power supply lines, which are operated as TN-C system. The main use of PIVM12,5-275/3+0 Vseries arrester is in structures of LPL III – IV according to EN 62305 ed.2. The marking M specifies a type of construction with removable module.
-
Product
LV Iron Core Shunt Reactors
-
Iron core Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system. Shunt Reactors are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. Shunt Reactors can be directly connected to the power line or to a tertiary winding of a three-winding power or distribution transformer.
-
Product
Low Voltage Power Supply Solutions
-
AC-DC Configurable. Advanced Energy is proud to offer highly reliable and cost-efficient low voltage power supply solutions. The Excelsys low voltage power supply product line has more than 20 years of experience of engineering power-density rich and extremely efficient supplies for a variety of markets.
-
Product
Gauss Meters
-
A gauss meter displays electromagnetic wave measurements in Gauss (G), milliGauss (mG), milliTesla (mT) or microTesla (µT) units. A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both. Thus, it is important to review the specifications of a gauss meter prior to purchase to ensure suitability for the intended application.Neodymium (NdFeB) permanent magnets are among the world's strongest and most widely used magnets. When testing magnets made of neodymium or other rare-earth elements, a gaussmeter or magnetometer capable of measuring DC magnetic fields is required. However, most electromagnetic fields encountered are generated by AC currents. Examples include electrical power lines, transformers and wiring for overhead lighting, solar panels and other electrical devices and equipment. Electromagnetic fields from electrical installations are believed to cause feelings of nervousness, anxiety and paranoia in EMF-sensitive human beings.Most gaussmeters offered by PCE Instruments can be calibrated and certified according to DIN ISO 9000 standards for an additional fee. Replacement gaussmeter probes and optional accessories are available for most gaussmeter models.
-
Product
Garden-Gard™ Garden Protection System
GPS-200
-
Parker McCrory Manufacturing Co.
*Protect gardens and shrubs from small animal damage*Portable – Go anywhere design*Fence controller operates on either a 12V battery or by using the 110V AC power adapter (both adapters included)*Power line convenience or 12V battery operated fence charger*Shocks through wet weeds and brush*Indoor/Outdoor installation*Weatherproof power connections*Low Impedance – safe to use with all types of fencing*Full three year warranty*Indicator light flashes to show fence charger operation*Weatherproof*100% American Made*UL Listed
-
Product
Femto / Picoammeter and Electrometer / High Resistance Meter
B2980A Series
-
Both the picoammeters and electrometers provide a world-best performance of 0.01 fA (0.01 x 10-15 A) current measurement resolution. In addition, the electrometers can measure resistance up to 10 P (10 x 1015 ), which is also a best-in-class specification. Finally, since AC power line noise can be difficult to eliminate when making low-level measurements, both the picoammeters and electrometers are available in battery powered versions.
-
Product
AC-Powered, AC Voltage Monitor
VAA/VQA
-
NAI’s VAA and VQA are AC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
Product
Programmable Industrial USB 3.0 Hub (8 Ports)
-
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
Product
Universal II Level System
-
The Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.
-
Product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
-
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
Product
20 Channel Actuator/GP Switch Module for 34970A/34972A
34903A
-
The Keysight 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
Impulse Noise Simulators
INS Series
-
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Product
EMI Receiver
KH3939
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
Product
Level System
Universal II
-
The Universal II level transmitter offers increased reliability, low maintenance and an intrinsically safe design for dependable level measurements in all kinds of process liquids, slurries, granulars and interfaces.Universal IIThe Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.When powered from an approved source this level transmitter can be made intrinsically safe. Its rugged contruction resists corrosion and abraision. The no moving parts design eliminates break downs.The Universal II level transmitter utilizes RF Admittance technology with manual calibration and a 4 – 20 mA output signal. The patented Cote-Shield circuitry ensures accuracy and reliability regardless of product build-up on the level transmitter.This level system is unaffected by changes in the process material density, pressure, or temperature variations.
-
Product
Ultrasonic Level Transmitter
USonic
-
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
Product
Fast Transient Burst Simulators
FNS Series
-
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
Product
Medical Electrical Safety Testers
-
Shanghai Beha Electronics Co., Ltd.
Special purpose AC milliammeter designed to measure hazardous leakage current from electrical appliances and other power line operated equipment.
-
Product
DALI Distribution And Commissioning
UBi
-
Every UBi can create up to 6 branches of a DALI line. Simply put a DALI line into one of the 2-way pluggable terminals, and then use any combination of the 5 remaining terminal pairs to route your cable anyway you like. Or, if you want the UBi to be a power supply, simply power a UBi Power with 24VDC and it will power your DALI line with 21.9VDC 245mA and still give you 5 DALI connections – one for your DALI controller and four to branch however you like.
-
Product
Lightning Surge Simulators
LSS Series
-
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
Product
Single Channel Signal Conditioner
SAM-3
-
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
Product
High Voltage Capacitance & Tan Delta Test Set
-
*Aesthetically designed Single Unit consisting of Measuring Bridge, Power Supply with in-built Standard Capacitor. Ideal for field /portable applications.*Highly compact & Portable – Approx 66Kgs only.*Advanced Protection Circuitry –specially suitable for 400kV s/s applications.*Successfully passed all required EMI/EMC Tests at SAMEER Chennai IEC 61000-4-2;IEC 61000-4-3; IEC 61000-4-4; IEC 61000-4-5; IEC 61000-4-11;*Improved Plug-in type of “Power In” and “Gnd” connectors.*Preo 2 Stage RF Power line Filters incorporated for 230V Power Input and Bridge Power Input for improved EMI Power line Protection*Improved 2 sets of LV measuring cables.*Improved HV cable outer covering hosepipe for rugged field use.
-
Product
DC Filters
-
This DC filter provides substantial noise reduction on DC power lines of up to 50V 9A. Filter provides noise suppression in both directions protecting your DC lines from noise generating by a particular piece of equipment or protecting your sensitive equipment from noise coming from DC power supply or other loads. DC filter provides noise suppression for both power lines – positive and negative, plus common-mode noise vs. ground. Filter uses plug-in terminal block for connections and mounting flanges for easy installation. Its rugged construction makes it easy to fit in many industrial tools.
-
Product
Programmable AC Power Source
LSX Series
-
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
