-
Product
Waveguides
-
A waveguide attenuator is an RF device specifically designed to reduce the power of a signal without affecting or reducing the waveform of the signal.
-
Product
HandyScope HS3: 10 MS/s 100MHz BW, 2 Channel, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS3-10
-
The Handyscope HS3 is a powerful computer controlled measuring instrument that consists of four measuring instruments: a Voltmeter, Oscilloscope, Spectrum analyzer and Transient recorder. Also an AWG (Arbitrary Waveform Generator) is available. This new powerful and compact measuring instrument can solve almost every measurement problem.
-
Product
Digital Wideband Transceiver Analysis
S94610B
-
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
Product
Arbitrary Function Generator PXI Card
GX1200 Series
Waveform Generator
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
PXIe-6544, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument
780992-02
Digital Waveform
PXIe, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument—The PXIe‑6544 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXIe‑6544 can sample digital waveforms at up to 100 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6544 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 16 Channels
DN2.653-16
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
Frequency Response Analyser
DP-cPCI-7554
-
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
Product
I2C Protocol Analyzer
EasyI2C
-
It's simple to find an I2C-style bus within arm's reach. Every computer, monitor, television and cell phone has it. Most microcontrollers directly support this protocol as well. Even so, the I2C protocol has many subtle nuances that are hard to grasp and easily forgotten. EasyI2C (TM) helps you to figure out exactly what is happening, without having to examine huge waveform trace capture files or set up complex tests.
-
Product
Digital Wattchman Monitor/Alarm Systems
Model 91091
-
The Coaxial Dynamics 'Digital Wattchman' Rack Mounted Station Monitor/Alarm is similar in function and appearance to our 81090 Series except it is designed for the accurate measurement of complex RF Waveforms such as CDMA (Code Division Multiple Access), DAB (Digital Audio Broadcast), DTV (Digital TV) and HDTV (High Definition TV), as well as CW, AM and FM.
-
Product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Digital I/O Module
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
9GS/s 8 Bit, 4GS Mem 6CH 24 Markers AWG
P9086B
Waveform Generator
The Proteus P9086B, is a 9GS/s, six channel arbitrary waveform generator packaged in a 4U, 19” standalone box with a 9” touch screen and on board PC , offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P9086B offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
Low Current Probe 80A
695
-
Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition, the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
-
Product
Waveform Function Generators
-
Teledyne Test Tools generate fixed or arbitrarily defined waveforms and signals for use in the development, testing and repair of electronic systems.
-
Product
Mixed Signal Oscilloscope, 1 GHz 2 Analog Plus 16 Digital Channels
MSOX3102A
Oscilloscope
1 GHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Pulse Generators
-
Keysight Technologies offers the most comprehensive portfolio of stimulus solutions for the generation of digital and analog waveforms and data signals. The Keysight instruments cover a frequency range from 1 μHz to 56 Gb/s and an output amplitude range from 50 mV to 20V.
-
Product
Pulse Radar Reference Test Solution
-
Compact Reference Solution with ADP7104, M8195A, WR15CCU, WR15CCD, N5183B combines commercial off-the-shelf COTS modular hardware and software from Guzik, Keysight Technologies, KJ Microwave and Virginia Diodes, which provides a flexible testbed for radar waveform generation and analysis. Generate and analyze pulse radar waveforms. Pre-correct waveforms for overall channel response. Supports many topologies for radar transmitter / receiver testing (IQ, IF, RF, microwave, millimeter-wave).
-
Product
FMC, XMC & PMC
-
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
Product
Full Wave Recorder
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
5 / 10 / 20 MHz Multiwaveform Arbitrary Signal Generator
MASG Series
-
- Economic and Light Weight- Dual Output with Same Characteristic- 1µHz Frequency Resolution- 11 Built-in Waveforms and 5 User defined Arbitrary Waveforms- AM, FM, PM, PWM, FSK Modulation, Frequency Sweep and Burst Function- Built-in 100MHz Frequency Counter- Arbitrary Waveform Editing PC Software- USB Host, USB Device
-
Product
Tri-phase High Power Programmable AC Power Source
APS50000
-
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
Product
Programmable Multifunction Generator
IST 5800/5850
-
IST Information Scan Technology, Inc.
The IST-5800 series programmable multifunction generator is an exceptionally versatile and economical instrument for applications in R&D, Manufacturing Test, Service Repair and Training. Featuring an adjustable triple output power supply and waveform generator, it has the ability to provide power and signal sources for a circuit while the universal logic probe, auto-ranging frequency counter, and digital voltmeter allows you to simultaneously analyze and measure circuit activity.
-
Product
USB Modular Oscilloscopes
U270xA
-
Roughly the size of a paperback book, these low-cost USB oscilloscopes make it easy to perform essential measurements — waveforms, voltage, current, resistance, and more. Inject standard or arbitrary waveforms into the systems or devices you’re testing with Keysight USB oscilloscopes.
-
Product
Dynamic Signal Analysis Software
ObserVIEW
-
Vibration Research Corporation
View, edit, and analyze waveforms from recorded or live data. This powerful and efficient vibration analysis software package includes specialized modules for waveform recording and test generation.
-
Product
Oscilloscope
RTA4000
Oscilloscope
Designed with top class signal integrity and responsive ultra-deep memory, the R&S®RTA4000 brings the power of 10 to a new level. The Rohde & Schwarz designed 10-bit ADC plus class-leading noise and memory depth provides sharp waveforms, more accurate measurements and confidence when facing unexpected measurement challenges.
-
Product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
-
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
Product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
-
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
Product
PCIe-7822, Kintex 7 325T FPGA, Digital Reconfigurable I/O Device
785360-01
Digital I/O Module
The PCIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Semiconductor Curve Tracer
CS-3000 Series
-
*Max. Peak Voltage : 3,000V（HV mode）*Max. Peak Current : 1,000A（HC mode）*Equipped all models with LEAKAGE mode (Cursor resolution 1pA）*USB port for display hardcopy, waveform data (CSV format) and measurement setup SAVE/RECALL*LAN interface for Remote Control
-
Product
Function / Arbitrary Waveform Generator
DG1000Z Series
-
DG1000Z series function / arbitrary waveform generator is a multi-functional signal generator which integrates function generator, arbitrary waveform generator, noise generator, pulse generator, harmonic generator, analog / digital modulator, frequency meter and other functions.
-
Product
Power Transmitter
ITL-101
-
Power Transmitters measure precise power of any waveform generated by electronic circuits. The ITL-101 cannot only be used for stationary power measurements, but also for power control on machines using fast response option and bi-polar output option. For frequency inverter applications minimal use of energy is and issue and here the ITL-101 finds its place.
