DIP
Dual in-line Package
-
Product
16-Port Gigabit Unmanaged Switch
EKI-2716GI-R
-
Provides 16 Gigabit ports with Auto MDI/MDI-X, Supports 16 x 10/100/1000 Mbps Auto-Negotiation, Supports redundant 12 ~ 48 VDC power input. Supports one-touch DIP Switch Configuration: QoS/ Redundancy, Redundancy RSTP/STP/X-Ring function on two designated ports. Supports EMC Level 4 protection for extreme outdoor environments.
-
Product
DCDC
DP Series
-
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
Product
Engine Control
StepGenerator4
-
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
Product
ASA240
-
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
Circbord
8003
-
VECTOR Electronics and Technology, Inc.
Pad per hole & peripheral ground plane.0.085” Square pads etched around each hole on wiring side.Accommodates any type DIP IC device or discrete component.Single sided board with pads and peripheral GND plane on one side only.Single-sided with no etch and plating on reverse side.
-
Product
Plugbord
3682-2
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
3U CompactPCI 8-port Serial Communication Module
cPCI-3548
-
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
Product
16-Port Fast Ethernet Unmanaged Switch
EKI-2716EI
-
Provides 16 Fast Ethernet ports with Auto MDI/MDI-X, Supports 10/100 Mbps Auto-Negotiation, Supports redundant 12 ~ 48 VDC power input. Supports DIP Switch Configuration: QoS/BSP/VLAN, Supports EMC Level 4 protection for extreme outdoor environments.
-
Product
PLCC-to-DIP Adaptor
Series 352000/353000
-
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Vertisocket™ Horizontal Mounting
Series 800
-
Vertisockets Horizontal Mounting with Bifurcated Contacts. Aries offers a full line of VertisocketsTM for DIP packaging of LEDs, incandescent lamps, DIP switches, test points, etc. The variations of mounting position and pin configuration provide exceptional design freedom.
-
Product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
-
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
Product
Low Power Programmable AC Source with Transients
61500 Series
-
Chroma Systems Solutions, Inc.
Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface
-
Product
DIP LED Aging Tester
LS6100
-
Designed to measure the aging-life and color comparisons of 260pcs DIP LED. • 260 separate constant current supply • Aging functions: constant current, impact pulse, on-off mode • Range of forward voltage(VF): 5.0V • Range of forward current(IF): 1) constant current: 0-100.0mA 2) Impact pulse: 0-200.0mA • Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99% • Range of on-off circle: 0-9999H59M59S • Range of on-off times: 0-9999times • Range of aging time: 0-9999H59M59S
-
Product
Signal Splitters
-
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
Product
Hardened Media Converter, 1000Mbps, Multimode 850nm, SC
EKI-2741SXI
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP (mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
Universal ZIF (Zero-Insertion-Force) DIP Test Socket
Series X55X
-
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
Product
Handyscope TP450-50XM-W5
TP450-50XM-W5
-
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Product
Signal Conditioners
-
Datexel has a large range of Signal Conditioners. We manufacture Thermocouple Transmitters, that are either Head Mounted, Din Rail and we even have an OEM version that can fit inside an enclosure smaller than 1" x 1/4". These Temperature Transmitters are PC programmable or DIP Switch programmable. Some are isolated and accept input from various sensors such as RTD's, Thermocouples Voltages, Current, Resistance and Potentiometers. They have current outputs and we even have Temperature converters that have voltage outputs.
-
Product
Plugbord
3682
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience. Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
Shorting Plugs and Jacks
Series SP200 & SJ200
-
.040 [1.02] Shorting Plugs and Jacks. These shorting plugs and jacks are used in conjunction with Aries DIP strips, available separately, for your programming needs. Consult Data Sheet Nos. 16007 and 16008 for details.
-
Product
Thru-Hole 0.040 [1.02] Male DIP Strip
Series M40
-
Thru-Hole .040 [1.02] Male DIP Strips. These DIP strips are used in conjunction with Aries Shorting Jack SJ200, available separately, for your programming needs.
-
Product
SOIC and SOJ-to-DIP Adaptor
Series 45000X & 65000X
-
SOIC & SOJ to DIP Adapters. A cost effective means of upgrading to SOJ or SOIC...without changing your PCB layout.
-
Product
Hardened Media Converter, 1000Mbps, SFP
EKI-2741FI
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
Test Strips
-
High-quality Hach chemistry in an easy-to-use test strip. Simply dip the strip into the sample and compare the color to the colors on the bottle to determine the reading. The test strips are accurate, portable and inexpensive. Applications include potable water, waste water, swimming pools and spas, industrial process applications and more. Available parameters include chlorine, nitrate and nitrite, water hardness, alkalinity, chloride, ammonium and more. Hach offers a high-quality 5-in-1 test strip that measures free chlorine, total chlorine, hardness, alkalinity, and pH—all in one strip.
-
Product
24-Pin SOIC w/Package-to-22-Pin 0.400" DIP
22-304504-18
-
24Pin SOIC w/ Package to 22 Pin .4 DIP. A cost effective means of upgrading to SOIC without changing your PCB layout.
-
Product
Regenerative Grid Simulator
61800
-
Chroma Systems Solutions, Inc.
Power rating: Up to 300kVA, single or three phase outputOutput Voltage: 0~330V L-N / 0~570V L-L0~400V L-N / 0~692V L-L opt. without using a transformerOutput Frequency: DC, 30Hz~100HzMaximum power delivered down to 200VAC L-NFull 4 quadrant, fully regenerative up to 100% of output current ratingSpecifically designed for PV inverter, Smart Grid and EV related test applicationsProgrammable slew rate settings for voltage and frequencyProgrammable voltage and current limitsTurn on, turn off phase angle controlLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetParallel output for higher power applications (three phase only)
-
Product
Thru-Hole 0.040 [1.02] Female DIP Strip
Series F40
-
Thru-Hole .040 [1.02] Female DIP Strips. This female DIP strip is used in conjunction with Aries Shorting Plug SP200, available separately, for your programming needs.
