Headers
-
Product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Terminal Block
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
SparkFun MicroB USB Breakout
-
This simple board breaks out a micro-B USB connector's VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B USB to your project, but don't want to put up with soldering the tiny connector, this is the board for you.
-
Product
Cable Assembly Crypto / Tape
-
The Cable Assembly Crypto / Tape provides a method of interconnecting the IP-Crypto and IP-Tape from the carrier to the PCI Bezel [rear IO] when installed into a PCI machine. Most IP Carriers have 50 pin headers suitable for ribbon cable in use for the IP Module IO. The headers are located on the carrier and internal to the chassis. Interconnecting to the outside world can be an issue.
-
Product
Arduino CAN Shield
IFB-10003-AWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
Passive XMC-to-PCI Express Adapter
6067
-
The Technobox, Inc. P/N 6067 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O. JTAG signals are brought out to headers allowing users the option of connecting the two JTAG ports.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
-
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
1-, 10-, 40-Gigabit Ethernet Portable Recorder
Talon RTR 2735A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, approximately 25 pounds- Shock- and vibration-resistant SSDs perform well in vehicles, ships and aircraft- Records gigabit, 10-gigabit or 40-gigabit Ethernet streams- TCP and UDP protocols- Copper or optical interfaces- Aggregate recording rates to 4.0 GB/sec- Windows® Server 2016 workstation with a high performance Intel® Core™ i7 processor- Up to 61 terabytes of SSD storage to NTFS RAID solid state disk array- Multiple RAID levels, including 0, 1, 5, and 6- SystemFlow® GUI with Signal Viewer analysis tool- C-callable API for integration of recorder into applications- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
Product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
SIM Insert
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 1m
40-971B-200-1m-MM
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
SparkFun USB Type A Female Breakout
-
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
-
Product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix Topology Without Column Protection Resistors
782385-07
Terminal Block
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-KDP
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
Product
ArgoBot Kit
ROB-00001
-
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
-
Product
Process Analyzer, Vent Master™ Series
-
Parkers Vent Master is designed to isolate the analyzer from fluctuating outlet pressures by controlling the pressure of the collection header and pumping the effluent sample gases into the fluctuating system
-
Product
SparkFun Digital Temperature Sensor Breakout
AS6212 (Qwiic)
-
This SparkFun Qwiic Digital Temperature Sensor Breakout provides a combination of high temperature accuracy with excellent low power consumption using the AS6212 digital temperature sensor from ams AG. The sensor measures temperature data up to ±0.2°C; accuracy over a wide range (-40°C; to +125°C;) and consumes an average of 6µA in normal operation (0.1µA in standby). The AS6212 communicates via I2C and has eight available I2C addresses selected by a pair of solder jumpers on the board. The breakout routes the I2C interface to a pair of Qwiic connectors to work with our plug-and-play Qwiic Ecosystem but also routes the bus and other pins to a standard 0.1"-spaced PTH header for users who prefer a soldered connection.
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
Product
SparkFun MicroView
USB Programmer
-
The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not only program the module, but use it to interface with your computer, Rapsberry Pi, or other USB device. The programmer has both male and female headers which allow it to be plugged into a MicroView module and a breadboard at the same time, making prototyping quick and easy.
-
Product
JTAG Emulators
XDS100v2 Series
-
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
Header, i2 Micro iCon, Receiver, 84 Pin, for PCB Mounting
510109204
Header
Header, i2 Micro iCon, Receiver, 84 Pin, for PCB Mounting.
-
Product
ST VL6180X Time of Flight Sensor
SEN-36001
-
Highly integrated breakout board for the ST Micro VL6180X Time of Flight (ToF) range finder sensor. This sensor has many uses in the robotics, cell phone and gesture recognition space. It has two programmable GPIO pins, and most importantly, measures absolute distance up to 100mm. The SEN-36001 includes a VL6180X IC centered between two 4-40 sized mounting holes with onboard 2.8V LDO and voltage translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and all IC pins have been broken out to a 0.1" pin header. Example code for the Arduino platform is available below and includes code for both the proximity measurement and ambient light sensing capabilities.
-
Product
Semiconductor Yield Management Software
QuickLoad-Central
-
QuickLoad-Central is our new STDF filtering, analysis, reporting, managing, viewing and editing tool. It looks at all your STDF files before you need to, pulling out key information to pre-generate reports and help you quickly find the files you need. You can list files of interest with yield and header information on our dashboard, visualize your data, open pre-generated reports or push any information from them that you can think of to JMP, Excel or other analysis tools.
-
Product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
-
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 0.5m
40-971B-200-0.5m-MF
Cable Assembly
This male rear exit to ribbon cable 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
