Headers
-
Product
SparkFun SD/MMC Card Breakout
-
With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
3.6 GS/sec Ultra Wideband RF/IF Rugged Rackmount Recorder
Talon RTR 2749
-
- Designed to operate under conditions of shock and vibration- Sample rates up to 3.6 GHz in single-channel mode- Sample rates up to 1.8 GHz in dual-channel mode- Capable of recording RF/IF frequencies to 1.75 GHz in single-channel mode- Capable of recording RF/IF frequencies to 2.8 GHz in dual-channel mode- 12-bit A/D, with 16- and 8-bit packing modes- Real-time aggregate recording rates of up to 4.8 GB/sec- 4U 19-inch rugged rackmount PC server chassis- Windows® workstation with high performance Intel® processor- Up to 122 terabytes of SSD storage to NTFS RAID solid state disk array- RAID levels 0, 5, and 6- SystemFlow® GUI with signal viewer analysis tool- C-callable API for integration of recorder into application- File headers include time stamping and recording parameters- Optional GPS time and position stamping- See Datasheet for configuration options for playback, recording and storage capacity
-
Product
GPIB Serial Interface
Model 4804B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
-
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
-
Product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
Terminal Block
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Development System
FE-C450
-
* Emulates Dallas Semiconductors DS89C450 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Analog Interface Boards
Model 4861B OEM
-
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 1m
40-971B-200-1m-MF
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
3U PXI Express Board Virtex-5 Medium Speed Quad DAC
SMT759
-
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
Product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
Terminal Block
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
Product
MTM Ribbon Cable Interface
-
ELEGANT CONNECTIONS: The S91-MTM-RCI-1 Ribbon Cable Interface connects non-MTM equipment into MTM-based systems. Bridge external test tools to an MTM test-point carrier board (TPCB) using wired ribbon cable, headers, or terminal blocks.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Board Accessories
DN-20
-
DN-20 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with two 20 Pin Headers.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Connectors, Jumper - Black
INT-10901
-
Jumper for 0.1" (2.54mm) spaced headers. These are also known as a 'shunt'. These mate with the 0.1" square-pin headers and are the 'open' frame style. RoHS compliant.
-
Product
Power Interface Board 3 HE, 1PSU-Steckverbinder mit AC-Pins
106PIBM301-9001R
-
The PIB 3U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
3U Conduction Cooled Power Interface Board, VITA 62
106PIBV301-0000R
-
3U Conduction Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
SIM Insert
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
Product
Emulates Dallas Semiconductors DS89C420
FE-C420
-
* Emulates Dallas Semiconductors DS89C420 * 16K Code Memory * Real-Time Emulation * Frequency up to fmax at 3V and 5V * ISP Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 2m
40-971B-200-2m-MM
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
SHB12X-H3X24, Male InfiniBand to Differential Flying Leads, Shielded LVDS Cable, 1.5 m
196236-1R5
LVDS Cable
72-Pin, Female Flying Leads to 48-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable - The SHB12X-H3X24 LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS digital instruments or some NI 658x LVDS Adapter Modules for FlexRIO directly to individual header pins. This cable is intended for use with a custom breakout fixture. The flying-lead cable has three signals per grouping for positive, negative, and ground pin connections designed to plug directly into any 0.1 in. header connector. It is a shielded, 100 ohm cable.
-
Product
Board
Arduino Leonardo with Headers
-
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
Product
IEEE488 (GPIB, HPIB) PCI-E Interface Card - PCIe Base 1.0a Compliant
GPIB-PCI-E
-
The Windows software set is included with the GPIB card. It is a WDM driver and supports Windows XP/2k/Vista/7/8 (32- & 64-bit 7 & 8), on all PC compatible platforms. Libraries and header files are included for the Visual C++, Visual Basic, MINGW and Delphi development systems. An industry standard compatible GPIB-32.DLL supports nearly all applications designed for that interface, including applications developed for LabView 6+, LabWindows, Agilent VEE, TransEra HT-Basic, Agilent Intuilink, and more.
-
Product
52x LVDS Module
LVDS-MOD5
-
Curtiss-Wright Defense Solutions
The LVDS-MOD5 high density LVDS I/O module offers the benefits of simplified cable connectivity by using two digital I/O headers suitable for ribbon cables. The LVDS-MOD5 LVDS I/O module can be used for a mixture of 2.5V and 3.3V input and output signals depending upon the VCCO settings on the FPGA on any particular I/O bank.
-
Product
Emulates Atmel T89C51RD2 in 68-PLCC package
FE-51RD2\68P
-
* Emulates Atmel T89C51RD2 in 68-PLCC package * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
