Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
2 Channel 10 bit 4GS/s Digitizer
V1761
-
The V1761 comes in a VME form factor with 2 input channels. The communication to and from the board is provided through VMEBus and Optical Link interfaces. It can record fast signals from fast organic, inorganic and liquid scintillators coupled to PMTs or Silicon Photomultipliers, Diamond detectors and others, and save them with high efficiency and precision for offline advanced timing analysis.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-01
Current Input Module
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Photoelectric Sensors
-
Our distance-measuring photoelectric sensors work according to the triangulation or propagation time measurement principle, with a red light or laser. The highly compact sensors have wide measuring ranges and measure very accurately with short response times.
-
Product
Vacuum Discharge Test Equipment
DAC-VD-1
-
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
Product
MBE Technologies
-
When you’re creating thin films of exotic compound semiconductor materials one crystal at a time, you need a molecular beam epitaxy system that is configurable for different applications.
-
Product
Modular Solar Array Simulators
MP4300A Series
-
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
-
Product
PXIe-1065, 18-Slot (9 PXI Slots, 3 PXIe Slots), Up to 3 GB/s PXI Chassis
779730-01
Chassis
PXIe, 18-Slot (9 PXI Slots, 3 PXIe Slots), Up to 3 GB/s PXI Chassis—The PXIe‑1065 is designed for a wide range of test and measurement applications and provides a high-bandwidth backplane. The NI PXIe‑1065 has nine PXI peripheral slots, one PXI Express slot with system timing capabilities, three PXI Express slots, and four hybrid slots that accept both PXI and PXI Express peripheral modules.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
Fully automated Crude and Detergent Fibre analysis
Fibertec™ 8000
-
The Fibertec 8000 is a fully automated system for determination of crude fibre, detergent fibre and related parameters according to standard reference 'crucible' methods such as Weende, van Soest and other recognised methods. Approvals for the crucible method include ISO, EEC, AOAC, AOCS. The Fibertec 8000 provides unrivalled accuracy, the highest safety and the lowest operator time of any fibre solution.Parameters: Crude fibre, neutral detergent fibre, acid detergent fibre, acid detergent lignin. Sample types: Raw materials and finished products in Feed and Agriculture.
-
Product
Azure SQL Edge
-
Bring the security and performance of the Microsoft SQL engine to the edge with Azure SQL Edge running on ARM64 and x64 architecture. This productivity tool for edge computing combines new capabilities such as data streaming and time series with in-database machine learning and graph features. Develop your application once and deploy anywhere across the edge, your datacenter, and Azure. Get the Microsoft SQL database engine optimized for the edge for as low as USD60 per device.
-
Product
Multi-analyzer / Recorder
OR38
-
OR38 models are intended for advanced needs in acoustic and vibration analysis measurements, for R&D as well as for testing. OR38 is a synthesis of components usually used separately for measurements. OR38 includes an acquisition front-end, with conditioning and sampling, a time domain recorder and the resources required to provide real-time processing of all inputs.
-
Product
Panel-mounted Power Amplifier
PAC2000B
-
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
Product
Traffic Analytics Tool
NetFlow Analyzer
-
NetFlow Analyzer, a complete traffic analytics tool, leverages flow technologies to provide real time visibility into the network bandwidth performance. NetFlow Analyzer, primarily a bandwidth monitoring tool, has been optimizing thousands of networks across the World by giving holistic view about their network bandwidth and traffic patterns. NetFlow Analyzer is a unified solution that collects, analyzes and reports about what your network bandwidth is being used for and by whom.
-
Product
IntegraVision Power Analyzer, 4 Channels, 3-Phase AC
PA2203A
-
Achieve better power analyzer accuracyAddress multiple test scenarios with the flexibility of wide-ranging, isolated inputsVisualize transients, in-rush currents & state changes with a high-speed digitizerAnalyze voltage, current and power in the time and frequency domains12.1" touchscreen
-
Product
Wideband Swept Antenna, Cable Analyzer
SWR TRUE 3013
-
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
Product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
CAN Interface
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Stator Testing System for EV Motor
EVT531
-
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
Product
Silicon-Microphone 8Ch Auto Test System
BK9015
-
Based on the BK3011 MEMS Mic Tester, the BK9015 is our fully automatic 8 channel MEMS (Silicon) mic sweep tester. Testing up to 8 DUT's simultaneously, the BK9015 can test 8 mics simultaneously and sort them according to passing grade and cause of failure! Because it uses a sweep test, it can check characteristics for the entire frequency range. Your data can be viewed in real time or stored so you can analyze problems or trends.
-
Product
4-CH Lighting Control Module
AX92353
-
*4-CH independent constant current LED drivers (up to 1 A)*Supports strobe and trigger mode*Intensity control by software*Supports duration and delay time for LED output
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT M3K+
-
SCOT M3K+ measures and displays CLOSE, OPEN and CLOSE-OPEN times of Main contacts of 3 poles connected end to end, simultaneously. Ideally suitable for CBs with single break per pole.
-
Product
Electronics Consulting
-
Our approach to consulting is unique. We encourage you to participate in every phase of the study. We provide you with all the information and knowledge that you need to repeat the study and perform future studies independently. Our reports are detailed and comprehensive. A consulting project may get over in a set time period but we expect our relation to continue. Our mission is to empower you through our products and services.
-
Product
Programmable High Power DC Power Supply
ADG series
-
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
Product
Production and Laboratory OTDR
8000
-
The 8000 OTDR is the first of a new generation of OTDRs that has been designed specifically for optical fiber and cable test applications. Its revolutionary "performance first" optical design delivers unsurpassed optical performance, and its MS Windows operating system facilitates integration of the OTDR into manufacturing networks. These features, combined with unique data acquisition capabilities, significantly reduce the time associated with many aspects of the OTDR measurement process, making it possible for fiber and cable manufacturers to increase production output and reduce manufacturing costs.
-
Product
Optical Fiber Rangers
-
Fiber rangers are a form of test equipment functioning similarly to an optical time domain reflectometer (OTDR).
-
Product
Continuous Emission Monitoring Systems
-
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
Product
Real-Time Clock (RTC) ICs
-
ST offers a wide portfolio of real-time clock (RTC) ICs with parallel or serial interface, including ultra-low-power devices and the world’s smallest package with embedded crystal. Our devices offer many value-added features such as supervisory functions that include alarm, battery switchover, and reset as well as special features with time stamp, anti-tamper for secure applications and an integrated audio section.
-
Product
LAN (PoE) Expansion Kit (supporting Gbit Ethernet)
OP-SB89G
-
OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate.
-
Product
Test Development Solution
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete "turn-key" service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
Mechanical Products
-
*99 types of pin cut data are stored in the backup RAM and can be recalled whenever necessary.*Inputting unnecessary pins and cutting to the specified size is easy and clear as it is done while watching the pins appear on the LCD (liquid crystal display screen).*Changing to a different pitch can be done in a short time by simply replacing the sprocket and comb teeth.
