Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, 26-28 AWG
610110169
Signal Contact (ITA)
Primary mating contact 610110167. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin SGMC Connector, With Interlock
42-158-003-HI
Relay
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 16 Amp Power Multiplexer, Quad 2-Channel 1-Pole
40-662A-011
Multiplexer Module
The 40-662A-011 is a quad 2-channel, 1-pole MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 1m, 500 Port
A500RMR-T-1B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly isy is for direct connection to products using the 500-Pin SEARAY connector.
-
Product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps)
7-124422000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps).
-
Product
AC to AC Power Supplies, Output 0 to 25 VAC, 3000 AMPS, 75 KW, P/N 5955C
-
- AC to AC Power Supply, 84 KVA, 1 PH, 60 Hz, P/N 5955C- Input: 240 VAC, 350 Amps- Output: 0 to 25 VAC, 3000 Amps max- Back to back SCR is used to adjust the output voltage- Start / Stop push button- Power ON Light- Voltmeter and Ammeter are included to monitor output voltage and current- Indoor enclosure: 42″H x 32″W x 22″D- Estimated weight: (TBD)
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
Multiplexer Module
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps)
7-121966000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps).
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps)
7-221902000-036
Power Patchcord
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps).
-
Product
PXI/PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 0.5m, 250 Port
A500RMR-05F050D4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
Product
PXI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
40-635A-107
Multiplexer Module
The 40-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Godzilla High Current Probes, 150 Amp
HC500
High Current Probe
Current Rating (Amps): 150Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 260Full Travel (mm): 6.60Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,215Overall Length (mm): 81.66
-
Product
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-252914000-036
Power Patchcord
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 0.5m, 500 Port
A500RMR-T-0A050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products). Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 2 Amp, 250 Port
C500RMX-4SB-4B
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Signal, Patchcord, Receiver, 72", TriPaddle, 5 Amp, 22 AWG White Twisted Pair, Single Ended
7-104422000-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", TriPaddle, 5 Amp, 22 AWG White Twisted Pair, Single Ended.
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector, With Interlock
42-153-104-HI
Relay
The 40/42-153-104-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 37-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin D-type Connector
42-153-103
Relay
The 40/42-153-103 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin D-type male connector.
-
Product
80 AMP FUSE BUDDY TESTER
FB315
-
*Tests circuit current from 0 to 80A*Includes 20A maxi fuse for use with mini and ATC circuit testing*Resolution: .1A (100 mA)
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
Product
PXI 2 Amp MUX, Dual 8-Channel 4-Pole
40-635-007
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 2m, 500 Port
A500RMR-C-1B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 26-28 AWG
610110167
Signal Contact (Receiver)
Primary mating contact 610110169. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
