Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 1m, 250 Port
A500RMR-C-5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector
42-153-004
Relay
The 40/42-153-004 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector.
-
Product
PXI 2 Amp MUX, Single 32-Channel 2-Pole
40-635-002
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 1m, 500 Port
A500RMR-T-0A100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Zero-Drift Op Amplifiers
-
The zero-drift amplifiers from Analog Devices combine both auto-zero and a chopper to self-correct continuously for dc errors over time and temperature, enabling the amplifier to achieve microvolt-offsets and nanovolts per degree Celsius drift. By design, the zero-drift amplifier has no 1/f noise nor does it suffer from long-term drift.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110145
Signal Contact (ITA)
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap.Plated in 50µ" gold
-
Product
Mini Power Contact, ITA, 65 Amp, 8 AWG
610115125
Power Contact (ITA)
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.Operating Voltage & Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
Product
Signal, Contact, Receiver, TriPaddle, 5 Amp, .025" Round Post
610110179
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps)
7-123926000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps).
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWG
610110147
Signal Contact (ITA)
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWGThis contact primarily used in CASS applications.Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation Compliant
-
Product
PXI 10 x SPST 10 Amp Power Relay Module
40-160-001
Relay
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 18 AWG White Teflon, Single Ended (10 Amps)
7-101918000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", TriPaddle, 18 AWG White Teflon, Single Ended (10 Amps).
-
Product
Switch Amp
-
One of many potential designs, Teledyne RF & Microwave's switched amplifier covers 100 to 2000 MHz, providing 18 dB gain, phase matched to within ±1.0 degree. The primary RF input and a secondary calibration signal input are switched, then amplified, and split to two outputs. Gain balance between any of the two outputs is ± 0.5 dB. Output power at 1 dB compression is +14 dBm and input/output VSWR is 2.0:1 maximum.
-
Product
Quad 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-001
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector, With Interlock
42-158-103-HI
Relay
The 40/42-158-103-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
PXI 2 Amp MUX, Single 16-Channel 4-Pole
40-635-003
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PCI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
50-635A-003
Multiplexer Module
The 50-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
40-158-103
Relay
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-252912000-036
Power Patchcord
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps).
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
Product
IGBT Power Supply, 120 KW, 0 to 16 VDC, 7500 AMPS, P/N 6132C
-
IGBT Power Supply, 120 KW, P/N 6132CInput: 480 VAC, 3 PH, 60 HzOutput: 0 to 16 VDC, 7500 AmpsRipple does not degrade when the output voltage is reducedDigital remote with Voltmeter and Ammeter and potentiometers includedDimensions: 20.00”W x 67”H x 24.5”D.Estimated weight: 600 lbs.
-
Product
PXI 16 Amp Power Multiplexer, Quad 4-Channel 1-Pole (SP4T)
40-662A-001
Multiplexer Module
The 40-662A-001 is a quad 4-channel, 1-pole (SP4T) MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110113
Signal Contact (ITA)
Primary mating contact 610110177. (May mate with other Receiver contacts, as well.)Plated with 30µ" gold.
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps)
7-222902000-036
Power Patchcord
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps).
-
Product
PCI 2 Amp Multiplexer, Dual 32-Channel, 1-Pole
50-635A-005
Multiplexer Module
The 50-635A-005 is a dual 32-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
100 Amp Intelligent Power Management
IPMDS100
-
- Intelligent Power Management System- 3 - 20 Amp Single Phase Outlets- 3 - 40 Amp Three Phase Outlets- 2 - 60 Amp Three Phase Outlets- Automatic Load Shedding- 100 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
Product
PXI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
40-635A-007
Multiplexer Module
The 40-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
24V / 400 Amp Load
BD12-24P-12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 24V battery systems and is extremely cost effective.
-
Product
Godzilla High Current Probe, 100 Amp
HC375
High Current Probe
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
