Additive White Gaussian Noise
-
Product
Noise Monitoring Systems
-
It delivers 24/7 connectivity, continuous power capabilities, and a rugged design to simplify your long-term testing.
-
Product
Noise Generator
CNG-EbNo SNR
-
The UFX-EbNo is a fully automated precision signal to noise generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal power meter provides repeatable SNR waveforms for accurate signal generation.
-
Product
Impulse Noise Simulators
INS Series
-
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Product
Noise Figure Analyzers
NFA Series
-
Optimize for noise figure using the NFA Series of high performance noise figure analyzers, which are designed to make fast, accurate, repeatable measurements. Key features include the simple user interface, graphical display, data storage, selectable bandwidths and on screen limit lines for pass/fail testing. With the NFA Series reliable measurements up to 40 GHz are now available in a single instrument.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
Low Noise Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's low noise amplifiers typically exhibit noise figures below 5.5dB and output 1dB compression points up 8dBm. These amplifiers are economical choices for general purpose applications. KeyLink's low noise amplifiers can be categorized as follows.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
Product
Additional Products: 104 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Low Noise Amplifiers
-
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
Product
Low Noise Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include low noise amplifiers, gain blocks, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
Noise Dosemeters
-
Noise Dosemeters are a type of sound meter designed to measure the levels of noise exposure to an individual over a period of time. All of our dosemeters are compliant to IEC 61252: 1993 / BS EN 61262:1997 and offer high quality and reliable personal noise monitoring solutions.
-
Product
Noise Dosimeter
ASV5910-3
-
Hangzhou Aihua Instruments Co., Ltd.
*Attractivedesign, mini—sized and weighs only 85g*Modulardesign, cable—free and dual channels*Complywith IEC61672, IEC61252 and ANSI S1.25*Rechargeable lithium polymer battery*Softwarepackage, downloads to PC*Varietymounting methods
-
Product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
-
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
Product
Noise & Interference Generator
GPS7500
-
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
-
Product
Broadband Amplified Noise Modules
NC2000/4000 Series
-
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
Product
Broadband Coaxial Noise Sources
-
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
Product
Low Noise Amplifier
ZLNA-9K-6G-01
-
Low Noise Amplifier, Frequency 0.009~6000MHz, Gain 40dB, Noise figure 3.5dB, P-1dB power 8dBm, SMA Female
-
-
Product
Noise Monitoring System
NoiseTutor
-
Continuous monitoring of environmental data in remote areas has always presented a unique set of challenges. Typical solutions involve complex installations, frequent visits to remote locations to keep the system fully operational and require expert level attention to retrieve and share data amongst customers, consultants and project leads.
-
Product
Mechanical Noise Tuner Control
S93027B
-
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
Product
Environmental Noise Monitoring System
E-Box LITE
-
When you need to perform unattended noise measurements that are to be left outdoors, the very last thing you need is the hassle of complicated equipment.
-
Product
SNR Noise Generator
CNG-EbNo
-
The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signals are used to compare theoretical BER to SNR ratios, found in "waterfall" type graphs, with measured values from the DUT to evaluate different modulation schemes. Users can obtain higher yield through automated testing, plus increased confidence from repeatable, accurate test results. Standard units can be modified for specific customer requirements. Please consult the factory for pricing and availability of these requests.
-
Product
Playback And Noise Simulation
-
Our systems make sounds and vibrations perceptible – from the pure, aurally accurate playback of binaural recordings to the realistic reconstruction of sound fields and background noise.
-
Product
Noise Monitoring Station
HD2011NMT
-
HD2011NMT is a remote control Noise Monitoring Station with meteo parameters acquisition. It is designed to be part of a network of noise monitoring terminals or a stand alone unit.
-
Product
Phase Noise Measurement Solutions
-
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
Product
Occupational Noise Measurements
doseBadge
-
The doseBadge is the original wireless personal noise dosimeter. It is the ideal tool to carry out occupational and industrial hygiene noise measurements and provides a unique solution for these applications.
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Additional Products: 200 Pin D Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Online Noise Monitor
AWA5636-3
-
Hangzhou Aihua Instruments Co., Ltd.
Complies with IEC 61672 Class 2. Uuse in Noise On-line Monitoring, Connect to Noise Screen
