Memory Test Systems
-
Product
LT-500A Aging-Life Test System For LED Luminaires
-
Hangzhou Everfine Photo-E-Info Co., LTD
LT-500A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
Product
PCIe 4.0 Test Platform
PXP-400A
Test Platform
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
High Voltage Isolation Test Systems
HT 9460 and 9464
-
Accurate and non-destructive production testing of ac Isolation Voltage and Partial Discharge.With over 450 systems installed worldwide the 946X series of test systems are the standard and system of choice used by the majority of semiconductor manufacturers that produce optically isolated devices.
-
Product
Standalone with Drop-In Test Systems
800 Series ATE
-
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
Product
6-Axis Robotic Automated Testing System
AT6
-
The Instron AT6 is a flexible, robot-assisted testing solution featuring six axes of motion, purpose-built to automate tensile, compression, flexural, and lap shear testing in alignment with widely used ASTM and ISO standards. Its modular design accommodates a broad array of materials—including metals, polymers, elastomers, films, composites, and sutures—at force capacities up to 600 kN. Capable of processing up to 500 specimens without operator intervention, the AT6 enables true unattended or “lights-out” operation, significantly increasing throughput around the clock. Optional modules include stations for specimen measurement, automated strain measurement, environmental temperature chambers, and multiple test frames for simultaneous testing. The system also integrates smoothly with auxiliary devices such as durometers, hardness testers, and surface roughness testers, making it a robust solution for high-volume, high-efficiency testing environments.
-
Product
Acute 4GS/s 68 Channel Logic Analyzer With 32Gb Memory
Acute LA3068B+
-
*LA3000E+/B+ series logic analyzer*PC-based*68 / 136 channels*USB 3.0 interface, 12V power adaptor*4GHz Timing Analysis / 250MHz State Analysis*32Gb RAM*Active Probes*Logic, State, Protocol triggers
-
Product
Small Drop Test System
KRD41 series
-
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
Product
Low Voltage Burn-in and Test System
Max 450
-
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
Product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
Test Instrument
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Industrial Flash & Memory Solutions DDR4 Memory
-
SQRAM DDR4 memory modules perform at superior speeds of up to 3200 MT/s, a 20% reduction in power consumption, and higher capacity than DDR3.
-
Product
RAMCHECK LX DDR4 Memory Tester
INN-8686-DDR4
-
The RAMCHECK LX DDR4 quickly and accurately tests and identifies DDR4 DIMMs for servers and desktops, as well as laptop SODIMMs.
-
Product
Vehicle Electromagnetic Field Test System
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are the daily means of transportation for our public, and the electromagnetic pollution in vehicles has received more and more attention from the public. The newly revised mandatory standard GB27630-201X "Air Quality Evaluation Standard for Passenger Cars" intends to require the electromagnetic field in the vehicle as one of the indicators. The measurement method measures the magnetic field strength in the vehicle. Within the frequency range of 10Hz-400kHz, the electromagnetic field measurement results should meet the requirements of the public limit of electromagnetic exposure in GB8702-2014.
-
Product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
-
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
Product
Ultra-High Performance FLASH and DRAM Memories Test Solution
Magnum V
-
Teradyne’s Magnum V systems delivers high throughput and high parallel test efficiency for ultra-high performance FLASH and DRAM memories. Magnum V’s largest configuration delivers up to 20,480 digital channels at 1600Mbps per channel.
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Leak Test System
NorCom 2020
-
The NorCom 2020 batch inspects up to 500 devices per cycle for both gross and ultra-fine leaks. The system incorporates a patented full field interferometer that produces reliable, repeatable leak test results. The system eliminates the need for helium mass spectroscopy or krypton testing for fine, and bubble leak testing for gross leaks.
-
Product
Universal Testing Systems (Up To 300 KN)
3400 Series
-
Instron’s 3400 Series universal testing machines offer dependable performance across a broad spectrum of mechanical testing applications, with force capacities ranging up to 300 kN. These systems are well-suited for basic tensile, compression, flexural, peel, puncture, friction, and shear testing, and can be easily configured using a wide selection of grips and fixtures from Instron’s accessory catalog. Built with user safety and efficiency in mind, each system incorporates Instron’s proprietary Operator Protect technology, ensuring a secure and intuitive testing environment.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Silicon-Microphone 8Ch Auto Test System
BK9015
-
Based on the BK3011 MEMS Mic Tester, the BK9015 is our fully automatic 8 channel MEMS (Silicon) mic sweep tester. Testing up to 8 DUT's simultaneously, the BK9015 can test 8 mics simultaneously and sort them according to passing grade and cause of failure! Because it uses a sweep test, it can check characteristics for the entire frequency range. Your data can be viewed in real time or stored so you can analyze problems or trends.
-
Product
Meter Testing System
ASTel
-
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-72x24x12
-
The 6 foot wide Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
Product
Measuring Systems For Night Vision Systems
MTF Master IIT
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for MTF, SNR and EBI of Image Intensifier Tubes (IIT). The MTF MASTER IIT was specially developed to classify the quality of image intensifier tubes by the objective criteria of the MTF (Modulation Transfer Function).
-
-
Product
Partial Discharge Test System
TPP
-
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Product
Test System
ETS788XL
-
The 50/100 MHz ETS788XL system is the compact protable version of our ETS788. Made with the new high-performance precision components of our Griffin series, this portable powerhouse offers an optional tough road case and ready to go to any test site needed. Just pop off the covers and get started. Whether it's research, Failure Analysis, or single-event effects testing, his powerful member of the HiLevel family takes advantage of all of the tried and true features that have served users so successfully to date.
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
