-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A11
-
IR Carbon and Sulphur Analyzer LCSA–A11 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and oxygen purity of 99.5 %, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
Product
Prostat Contact Voltmeter
CVM-780
-
The CVM-780 contact voltmeter combines the ease of use of a digital voltmeter with the high impedance and low capacitance of a true electrostatic voltmeter, in a small, portable package.It reads the actual voltage, without interference from the electrostatic field strength. The ceramic tips of the probe allow precise measurement of values.Measurement of voltages up to 500 VDC.
-
Product
Digital Teslameters/Gaussmeters
-
S Digital Teslameters offer accurate, high resolution measurement of magnetic flux densities, withdirect digital readout in tesla or gauss, and serialcommunications by fiber optics or RS-232C for system applications.The instruments are light and compact, and the probes are easy to use. The DTM-151 has been engineered to withstandthe severe electrical interference produced by high voltage discharge.
-
Product
Flash SATA Disk /mSATA SATA 3 SLC,MLC
FSA 300 Series
-
*SATA III (6.0Gb/s) interface*Capacity: SLC 1 GB to 64 GB, MLC 4 GB to 128 GB*iSMART disk health monitoring*Intelligent error recovery system*Write protection security*Anti-vibration mechanical design*Excellent data transfer speed*Zero mechanical interference*JEDEC standard MO-300B dimension
-
Product
Ultra-High Resolution Spectrometers
-
Fabry-Pérot interferometers are optical resonators used for high-resolution spectroscopy. They use the phenomenon of multiple-beam interference that results when light shines through a cavity bounded by two reflective parallel surfaces. When the light hits one of the surfaces, some is transmitted out, and the remaining part is reflected back. Fabry-Pérot produces a circular fringe pattern, similar to the Michelson pattern. However, the fringes are thinning, brighter, and more widely spaced. As a result, these instruments are able to detect and resolve the fine features of a transmission spectrum with high precision.
-
Product
Fast Tuned Notch Filter
ES005 & ES006
-
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
Product
VXG Vector Signal Generators
-
Keysight's VXG vector signal generators offer the industry's highest output power with ultra-low phase noise for your most demanding wireless and aerospace and defense applications. With the VXG's multichannel architecture, quickly switch from blocker and interferer tests to MIMO and beamforming tests.
-
Product
USB 2.0 Interface Module
-
USB 2.0 modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 2.0 link untouched.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Interferometers
-
An instrument in which the interference of two beams of light is employed to make precise measurements.
-
Product
Optical Oxygen Sensors
-
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
Product
Modulation Distortion Up To 13.5 GHz
S930701B
-
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Advanced IR Gas Analyzer For Process Monitoring
T-Series
-
T-Series Inline Gas Analyzer improves gas measurement accuracy over the traditional non-dispersive infrared (NDIR) analyzers using Tunable Filter Spectroscopy (TFS™), a spectroscopic scanning technique capable of generating slices of spectra in the infrared region. Each scan produces an absorption spectrum which is used to identify compounds and provide concentration values. TFS technology improves gas identification accuracy and selectivity by subtracting out spectra from interferent gases within the same infrared regions. This spectral processing capability also provides multi-component measurement.
-
Product
Microwave Coaxial Cable Assemblies
MWX0 series
-
JUNFLON® MWX products are flexible signal transmission lines that take advantage of the remarkable properties of fluoropolymers. They are suitable for use with a wide range of frequencies up to 67 GHz. These products feature low insertion loss and low VSWR, low signal leaks and low interference due to high shielding effectiveness, and higher density wiring for use in the narrow device interiors. Junkosha provides highly reliable products for microwave /millimeterwave applications tailored to customer assembly needs.
-
Product
Signal Acquisition and Filtering Technology
SNAPTrack®
-
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
Product
Quantum Accelerometer
-
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
Product
XYZ Color Sensor
AS7261
-
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
-
Product
Automatic Capacitance and Tan Delta Bridge
-
*Automatic Microprocessor controlled Guarded Bridge Circuit.*Suitable for testing at voltages up to 500kV.*Can be used to measure both Grounded and Un-Grounded Specimens.*Automatic guard circuit for three-terminal measurement.*Interface measurement and automatic interference suppression circuitry.*Optional range Extension Transformer for large capacitance values.*Test data storage facility.*RS-232 computer interface and USB printer interface.*Window Interface Software for data transfer.
-
Product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
-
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Premanaged Gigabit Ethernet Switch
XES-2T6
-
The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
-
Product
Electromagnetic Simulation Software Suite
EMTOOLS
-
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
-
Product
Test tools
-
Try our low-cost RF sniffers for fast and easy troubleshooting of unwanted interference caused by electromagnetic radiation sources in your local environment.
-
Product
Upright Microscopes
-
ACCU-SCOPE upright microscopes deliver top quality optics for bright, crisp images. Sometimes referred to as compound microscopes, our upright microscopes are favorites across a wide range of laboratories including clinical, veterinary, pharmaceutical, research, university, and education. Some of the disciplines utilizing our upright microscopes include pathology, hematology, microbiology, cytology and histology. ACCU-SCOPE upright microscopes offer a selection of magnifications from ultra-low (e.g. 2X) to high power oil immersion (e.g. 100X). Our microscopes have a variety of options and accessories to perfectly fit your application including ergonomic viewing heads, trinocular heads for camera attachment, and an assortment of objectives. Common contrast methods used with our microscopes include brightfield, phase contrast, darkfield, Differential Interference Contrast (DIC) and fluorescence.
-
Product
Application Specific LC Systems
Co-Sense for LC-MS
-
In LC-MS, there are various factors which may preclude the applicability of HPLC with MS analysis, including the interference associated with non-volatile buffers often used in HPLC. Therefore, tedious procedures are adopted, in which separation and collection is conducted by HPLC, and after desalting and other processing, MS measurement is performed.
-
Product
Insulation Resistance Meter
AMIC-15k1
-
The partial discharge indicator PDI. Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD. Allows to test the electrical durability of the tested object - indication of breaking voltage. The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
Product
EMI Receiver
KH3939
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
Active Dual Loop Antenna
KH30936
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
