-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Ultra-High Resolution Spectrometers
-
Fabry-Pérot interferometers are optical resonators used for high-resolution spectroscopy. They use the phenomenon of multiple-beam interference that results when light shines through a cavity bounded by two reflective parallel surfaces. When the light hits one of the surfaces, some is transmitted out, and the remaining part is reflected back. Fabry-Pérot produces a circular fringe pattern, similar to the Michelson pattern. However, the fringes are thinning, brighter, and more widely spaced. As a result, these instruments are able to detect and resolve the fine features of a transmission spectrum with high precision.
-
Product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
Product
Superconducting QUantum Interference Device (SQUID) Magnetometer
Quantum Design MPMS®3
-
Quantum Design's MPMS 3 represents the culmination of 40 years of development and design in the world of SQUID Magnetometry. Providing users with the sensitivity of a SQUID (Superconducting QUantum Interference Device) magnetometer and the choice of multiple measurement modes, the MPMS 3 offers new levels of performance in magnetic research while including those aspects of past Quantum Design SQUID magnetometers that customers have grown to appreciate and depend on.
-
Product
SatGuard
-
Kratos Defense & Security Solutions, Inc.
SatGuard can help resolve in minutes, revenue loss problems that have lasted weeks, months or longer. The VSAT monitoring and mitigation product from Kratos classifies VSAT networks and identifies the specific IDs of the terminals causing interference to much more quickly resolve issues.
-
Product
Nanostructuring
-
AMO offers a highly flexible process-platform for the fabrication of nanostructures. We have a broad range of lithography techniques that can be flexibly combined with each other – including interference lithography. Each lithography technique is tailored to a specific pattern-transfer process and can be used on a wide range of substrates. In addition, we have developed an advanced nanoimprint lithography process that can transfer e-beam-defined patterns to large areas in a cost-effective manner.
-
Product
Modulation Distortion Up To 13.5 GHz
S930701B
-
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
ISN / T-Networks
-
Is used to measure the asymmetrical interference voltage on symmetrical data or telecommunication lines.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
Voltage Probe
KHZ43201
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
Product
Temperature Data Logger
-
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
Product
Modulation Distortion Up To 90 GHz
S930709B
-
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
Product
Distributed I/O
-
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
-
Product
AGV Magnetic Guide Sensors
-
MultiDimension Technology Co.,Ltd.
Are adaptive to installation height and tape width with excellent protection against magnetic material interference. Incorporating tunneling magnetoresistance (TMR) technique, the AGV-TMR15X series are designed to provide excellent temperature characteristics, good consistency, fast frequency response, high sensitivity and low power consumption performance.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
WiFi Traffic Generators
LANforge WiFIRE
-
wireless traffic generator is an excellent choice for testing Access Points and other WiFinetworks. The CT520 uses a modified Wireless driver for WiFi NICs based on the Atheros chipset. It cansupport up to 32 Virtual Stations. Each of the Virtual Stations has its own IP address, IP port space, MACaddress and routing table. The Virtual Stations can be assigned to communicate to a particular AccessPoint, use a particular SSID, and have a WEP (64 or 128bit) or WPA/WPA2 key assigned. More advanced802.1X authentication is also included. There is a single WiFi radio per CT520 but multiple LANforgesystems can be clustered together for more realistic radio interference patterns and increased trafficgeneration capability. The radio supports 802.11 a, b, g or n mode. Transmit power andchannel/frequency is configured on a per-radio basis. Most other settings are configurable per virtualstation
-
Product
Spectrum And Signal Monitoring
-
Kratos Defense & Security Solutions, Inc.
With the rapid growth of satellite networks including VSATs, there is the potential for increased Radio Frequency Interference (RFI). Interfering signals can be periodic or occur at different frequencies over time, making the discovery and removal of these sources a significant challenge.
-
Product
Upright Microscopes
-
ACCU-SCOPE upright microscopes deliver top quality optics for bright, crisp images. Sometimes referred to as compound microscopes, our upright microscopes are favorites across a wide range of laboratories including clinical, veterinary, pharmaceutical, research, university, and education. Some of the disciplines utilizing our upright microscopes include pathology, hematology, microbiology, cytology and histology. ACCU-SCOPE upright microscopes offer a selection of magnifications from ultra-low (e.g. 2X) to high power oil immersion (e.g. 100X). Our microscopes have a variety of options and accessories to perfectly fit your application including ergonomic viewing heads, trinocular heads for camera attachment, and an assortment of objectives. Common contrast methods used with our microscopes include brightfield, phase contrast, darkfield, Differential Interference Contrast (DIC) and fluorescence.
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
EMI Receiver
KH3939
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
Product
System Analyzer
H60
-
A meter conceived for professionals that know what they want. Functions for CATV systems, MATV systems and IRS systems done in coax or fibre. For free to air or encrypted programs, the H60 features unprecedented capacities for a meter of this size. There is simply no possible comparison with others, Capacity to measure any wanted signal or interference up to 3,3 GHz. The best way to analyze the TV or telephony (GSM or LTE/4G) equipment or installations.
-
Product
Paramagnetic Oxygen Analyzer
Model T802
-
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T802 comes with the NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
High Range UV Fluorescence SO2 Analyzer
Model N100H
-
Teledyne Advanced Pollution Instrumentation
The Model N100H instrument uses the proven UV fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high range SO2 gas. The instrument includes interferent rejection, providing a simple and precise solution for a broad range of continuous emission monitoring systems (CEMS) and stack testing applications.
-
Product
Anti-Interference Test Equipment
-
Beijing KeHuan Century EMC Technology Co,.LTD
Anti-Jamming Test Equipment.
-
Product
Application Specific LC Systems
Co-Sense for LC-MS
-
In LC-MS, there are various factors which may preclude the applicability of HPLC with MS analysis, including the interference associated with non-volatile buffers often used in HPLC. Therefore, tedious procedures are adopted, in which separation and collection is conducted by HPLC, and after desalting and other processing, MS measurement is performed.
-
Product
EMC Testing Inductors
-
Electromagnetic Compatibility (EMC) testing is a somewhat unique discipline within the world of electrical product development and analysis. Electromagnetic Compatibility (EMC) testing is primarily concerned with understanding and mitigating the affects of Electromagnetic Interference (EMI).
-
Product
Modulation Distortion Up To 26.5 GHz
S930702B
-
S930702B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 26.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930702B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Interactive Software
TE SERIES
-
The TE SERIES Interactive Software provides a powerful set of formats and charts for fast analysis, and interfaces with a simple USB. Features include smith charts, multi series plotting, difference plotting, curve smoothing, annotations, cursors, time domain reflectometry and interference spectrum scanning.
