Identification
See Also: Identify, ID, Machine Learning
-
-
Product
Cable Identification & Phasing
VCi-3™
-
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
Product
AXIMA Microorganism Identification System
-
The AXIMA Microorganism Identification System presents a new solution for the identification of microorganisms for microorganism research in the pharmaceutical, food, science, energy, environment, clinical and health fields.
-
-
Product
Portable Radioisotope Identification Devices (RIIDs)
-
ORTEC Detective Family Hand-Held Radioisotope Identifiers (HHRIIDS or RIIDS) have been in the front line of operations to interdict the illicit trafficking of nuclear materials worldwide, ORTEC RIIDS are used every day.
-
Product
Hand-held Radioisotope Identification Device
RadEAGLET
-
Combining a large, high sensitivity crystal with a proven and tested intelligent algorithm, the RADEAGLET can quickly, accurately, and simultaneously detect and identify up to six isotopes, typically in under 30 seconds. The RADEAGLET performs well, even in complex shielded or masked scenarios. ANSI 42.34 compliant, the RADEAGLET offers a user-friendly interface that is intuitive, simple to navigate, provides visually clarity, and utilizes an extensive array of alarms. Supports NaI(Tl) and LaBr3(Ce) to optimize performance across multiple applications.
-
Product
Chemical Weapons Identification Systems
-
Portable Isotopic Neutron Spectroscopy (PINS) Systems have been deployed world-wide; increasingly, being deployed as part of national counter-terrorist efforts. PINS provides a non-contact and non-destructive means of identifying the CHEMICAL contents of "suspect" packages.
-
Product
Energized Cable Identification System
LCI™
-
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Product
Cable Identification System & Cable Phasing System
Impulse Phaser
-
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
Product
All Hazards Detection & Identification Tool
MX908
-
MX908™ leverages high-pressure mass spectrometry (HPMS) to deliver dramatically enhanced sensitivity and broader threat category coverage. MX908 hosts an all hazards threat list which has been upgraded to include a broader spectrum of chemical warfare agents (CWA), explosives and high priority toxic industrial chemical (TIC) targets. From military grade, commercial and improvised explosives to novel threat materials, MX908 supports the needs of the modern mission.
-
Product
Intelligent identification
RFID
-
Radio-based RFID technologies in the HF (high frequency) and UHF (ultra high frequency) ranges supplement SICK’s industrial automation portfolio. In applications where process-relevant data is modified remotely, RFID makes it possible to store data on writable and rewritable media. And, in contrast to optical solutions, RFID provides reliable identification of all objects – despite dirt and everyday wear.
-
Product
True Phase Identification System
SPI-III™
-
Our vision has always been to create a phase identification system that exceeds any of today’s industry quality, safety and efficiency requirements. SPI-III’s unique design consists of a wireless bi-module combo that is stunningly easy to configure and operate. With many advancements and innovations, SPI-III will be more helpful than ever before, enabling field applications such as identification of A-B-C electrical phases from all 50 and 60 Hz networks, switchgear phase concordance (matching), phase rotation, system paralleling, underground phasing applications and more.
-
Product
Cable Identification System
KSG 200 / KSG 200 T
-
Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V
-
Product
Material Identification Spectroscopy
ChipCHECK
-
Gastops specializes in advanced fluid sensing and analysis systems specifically designed and developed for critical equipment condition monitoring applications. ChipCHECK offers the fastest way of making on-site equipment maintenance decisions. It is a field deployable analyzer designed for rapid on-site identification of equipment lube oil. This automated maintenance decision-support tool employs innovative laser spectroscopic technology, which enables on-site analysis of microscopic chip debris. ChipCHECK provides the maintainers with quick, reliable, and conclusive information, including the total number of particles, and the size, shape, and specific alloy classification for each individual particle on the sample.
-
Product
Automated System for Identification and Control of Pharmaceutical Codes
-
The automated system for identifying pharmaceutical codes includes two scanners of the pharmaceutical code, two sensors for the presence of an object and a data processing unit (BOD). When the box or instructions are passed under the object presence sensors, the farm code is read by the corresponding scanner and the results are transmitted to the computer via the Ethernet interface. The BOD verifies the correctness of the read out farm code by comparing this code with the reference farm code set at the beginning of the system operation. If the farm code has not been read or does not match the standard, the packaging machine stops and the type of error is displayed on the indicators.
-
Product
Power Quality Measurement & Digital Fault Recording
-
In view of the growing number of factors with a disturbing influence on power systems and the ever increasing sensitivity of devices and installations on the consumer side, simple monitoring criteria such as undervoltage or overcurrent are no longer adequate. Reliable registration of all the relevant processes within the electrical power system calls for constant observation of a wide variety of derived parameters, such as individual harmonic content, system unbalance and interharmonics, and the swift identification of even slight deviations from the norm.
-
Product
Remote Spectrum Analyzers
LPT-3000RX4
-
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
Product
12-42V LED Heavy Duty Circuit Tester
1651A
-
Peaceful Thriving Enterprise Co Ltd
*Check on 12 - 42V systems. *Automatic voltage identification: BLUE LED for General car / RED LED for Hybrid car.
-
Product
Phase Detector
Paula
-
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
Product
Voltage/Continuity Tester
VOT-50
-
Standard Electric Works Co., Ltd
● Voltage test: 12V to 690V AC/DC (7 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 127V, 230V, 400V, 690V.● Polarity test: LED +/-● Audible continuity test● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP54● Phase / Neutral identification● Integrated storage clips for test probe.● Rubberized injection molding.
-
Product
Conveyor X-ray Scanners
-
Innovative baggage X-ray screening units for quick and easy identification of the material composition of scanned objects.
-
Product
Model And Resonance Testing
-
Response Dynamics Vibration Engineering, Inc.
Resonance identification, dynamic testing, modal analysis and operating deflection shape analysis, form the basis of our set of expertise in vibration analysis, and are described on this page, in the embedded video below, and in the links above in more detail. This is the heart of vibration testing and key to making a confounding vibration issues understandable. Our vibration testing, structural dynamics and modal analysis consulting services have helped push the limits of technologies and cutting edge designs for over 30 years.
-
Product
Ethernet PHY
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
Product
StellarCASE Analyzers
-
StellarNet proudly announces new rugged and fully integrated portable Case Spectroscopy Systems for material identification, elemental and composition analysis using Raman, NIR & LIBS technologies. The StellarCASE Systems include interior mounting of spectrometer instrumentation pre-configured for “Open & Measure” application, with no additional setup required. With a simple press of the “Analyze” button instantaneous composition analysis or material/elemental match results are displayed on your screen. The StellarCASE systems feature an internal main power control system with ON, OFF, & Charge buttons and an 8 hour battery life for portable field applications. Also, includes AC power adapters for use in the laboratory and classroom.
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
Product
Cable Fault Locator
TX4000
-
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
Product
ESD Tester
GZ600 HID
-
• Personal equipment tester with badge reader• Compact• LCD digital display• Identification by RFID badge• Possibility to program test parameters for each employee• Allows communication with the company network or the dedicated server (SQL database)• Supplied with a shoe test mat• 4 test modes: bracelet / shoes / bracelet and shoes / bracelet or shoes
-
Product
LED Tester For Chip And Wafer
-
Electrical Testing: Forward：VF,DVF,VFDReverse：VZ,IROptical Testing: can test LOP in cd/mcd/W/mW/lm... from different optical componentsWavelength λp,λd,λc,hw,purity,(x,y),CCT,CRIFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Compatible mechanical interface.Optional ESD static test system or polycrystalline test system
-
Product
Phase ID Systems
-
LED Meter Probe allows the user to take Real time Phase Angle readings along with AC nominal voltage readings. A PD800W LED Meter Probe works in conjunction with the Receive Unit to verify phase identification along with the actual phase angle data. This is all done without any calculations or data transfer from the field to a base computer. The meter probe and reference probe or receive unit can operate at 100 feet of separation and up to 300 feet line of sight separation. In the event that this distance would need to be greater, the Receive Unit can be unplugged from the charging cable and taken into the field while operating on it's rechargeable batteries for up to 8 hours at a time.
-
Product
Counterfeit Analysis / Screening Services
-
DPACI perform counterfeit part analysis on all types of electrical, electronic, and electromechanical (EEE) components. Our suspect counterfeit analysis task groups include source identification, manufacturer validation, external visual inspection, mechanical inspection, electrical test, X-Ray, in-depth internal visual and materials analysis. With one of the largest databases of test reports for EEE components, we can offer similar historical data for correlation with images, test data, certifications and reports.
