Identification
See Also: Identify, ID, Machine Learning
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
-
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
-
Product
Portable Spectrometers
-
*Quick search and detection of gamma radiation sources with radionuclide identification*Measurement of gamma radiation ambient dose equivalent rate
-
Product
Thumpers and Cable Fault Location
-
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
Product
Data Analytics
-
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
Product
Empowering Traditional Mass Spec
ZipChip
-
The ZipChip™ separations platform uses integrated microfluidic technology to prepare, separate and electrospray biological samples directly into traditional mass spectrometers (MS). In less than 3 minutes per sample, the cost-effective ZipChip system enables analysis of a broad range of matrices from growth media to cell lysates, blood, plasma, urine, and biopharma products. Each chip provides answers on analytes from small molecules up to intact proteins, antibodies and antibody drug conjugates (ADCs). This platform provides better separation quality than most liquid chromatography (LC) instruments – in a fraction of the time – all with full MS identification behind every separations peak.
-
Product
LCR Meter
-
Basic measurement accuracy 0.1% & speed upto 10 meas / secLarge LCD display with bright white backlightUltra low power consumption, battery powered for 24hours of continuous useAutomatic identification function (Ai).Percentage display & 4 tolerance comparator : 1%, 5%, 10% & 20%9V battery & External power supplyAutomatic correction function with datahold, max. / min. / average recordingUtility function configuration & current setup recovery after power offStandard Mini-USB interface, SCPI compatibleAuto power OffConstant output impedance : 100 ohm
-
Product
Constantan, Type T (°C) Contact
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
Optical Fiber Identifier
-
Anfkom International Co.,Limited
It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.
-
Product
Analytical Instrument
LabSpec 4 Hi-Res
-
Analytical Spectral Devices, Inc.
The LabSpec 4 Hi-Res analytical spectrometer is designed for analysis of materials that are characterized by sharp spectral features that may require more resolute spectral data for accurate detection and identification.
-
Product
Male/Female DIP Jumpers
Series 200 thru 216
-
Male/Femaie DIP Jumpers. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Stationary 1D Bar Code Readers
-
Leuze electronic GmbH + Co. KG
In production and logistics, the identification of goods and materials through universally usable 1D bar codes controls many processes. The areas of application of our readers are accordingly diverse – from miniature scanners to compact scanners and bar code readers with large reading distances for industrial application. Modular systems, pre-mounted for intralogistics or bar code scanners for specific industries, e.g., for laboratory automation, round out the areas of application. Scanning rates of up to 1,000 scans/s, small installation dimensions, robust housings and integrated heating for use in deep-freeze areas meet the individual requirements of your application.
-
Product
Deci-Center™ Jumpers
Series 112, 113 & 114
-
Deci Center Jumpers. Reliable, electronically tested solder connections. Pitch bars help maintain .100 [2.54] conductor spacing. 10-color cable allows for easy identification and tracing.
-
Product
Refrigerant
-
The Mentor Automotive Refrigerant Identifier portfolio provides simple and accurate refrigerant analysis. The Mentor is a user-friendly, cost effective R-1234yf and R-134a refrigerant purity analyzer designed with state-of-the-art non-dispersive infrared (NDIR) technology for the identification of refrigerant gases in automotive air-conditioning systems.
-
Product
XRF and XRD Analyzers
Vanta
-
The Vanta analyzer is our most advanced handheld X-ray fluorescence (XRF) device and provides rapid, accurate element analysis and alloy identification to customers who demand laboratory-quality results in the field. Vanta handheld XRF analyzers are built to be tough. Their rugged and durable design makes them resistant to damage for greater uptime and a lower cost of ownership. With intuitive navigation and configurable software, the Vanta series are easy to use with minimal training for high throughput and a fast return on investment. Featuring innovative and proprietary Axon technology, Vanta analyzers give you accurate results and help boost productivity no matter the environment or working conditions.
-
Product
Entry Level Loss Tester
Model：OLT-20
-
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
Product
Fibre Tracer
FT20
-
The KD Optics FT-20 is a small, hand-held, visible source used for tracing multimode fibre optic cables and is especially useful for identifing a single fibre in a multi-fibre cable. The unit has a bright LED output with a 2km range and is modulated at 2Hz.
-
Product
Cable Identifiers
-
*Identifies matching phase on long deenergized and discharged conductors*50VDC test voltage enables identification of up to 5,000 foot-long conductors*Compact, lightweight and easy-to-use solution*Versatile for overhead and underground applications
-
Product
TestTools for Lab & Field
-
Analyzer designed to be used on the field to generate maps including measurements of the field quality of service, enabling identification of reception issues and efficient troubleshooting.
-
Product
Microbiology & Diagnostics
-
The number and diversity of microorganisms infecting humans and animals are ever increasing. Understanding how microbes cause disease and evade treatment is crucial for the protection of global public health. Bruker supports researchers and healthcare providers in the rapid identification and analysis of microorganisms.
-
Product
CBRN Detectors
RIID
-
A Radioisotope Identification Device (RIID) is a small, lightweight, portable instrument that identifies radioactive materials by measuring the energy of gamma rays they emit. RIIDs can also perform spectroscopic analysis to distinguish between different radioactive isotopes.
-
Product
100Hz/120Hz/1kHz/10kHz/100kHz Handheld LCR Meter
U1733C
-
20,000 counts resolution0.2% accuracy Wide LCR ranges with 5 selectable test frequencies (100Hz, 120Hz and 1kHz, 10kHz and 100kHz)Auto identification(Ai) which automatically determines and displays component type and measurements Detailed component analysis with DCR, ESR, Z, D, Q, functions Battery life of 16 hours/Ac-powered IR-to-USB connectivity for data logging to PC
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 0.5m
40-971B-200D-0.5m-MF
-
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
Product
EDX-FTIR Contaminant Finder/Material Inspector
EDXIR-Analysis Contaminant Finder/Material Inspector
-
EDXIR-Analysis software is specially designed to perform qualitative analysis using data acquired by an energy dispersive X-ray (EDX) fluorescence spectrometer and a Fourier transform infrared spectrophotometer (FTIR). This software is used to perform an integrated analysis of data from FTIR, which is excellent at the identification and qualification of organic compounds, and from EDX, which is excellent at the elementary analysis of metals, inorganic compounds and other content. It then pursues identification results and the degree of matching. it can also be used to perform EDX or FTIR data analysis on its own. The library used for data analysis (containing 485 data as standard) is original to Shimadzu, and was created through cooperation with water supply agencies and food manufacturers. Additional data can be registered to the library, as can image files and document files in PDF format. It is also effective for the linked storage of various types of data as electronic files.
-
Product
Wheelset Axle Identification Using 2D DMC Codes
-
Automation of the process of identifying the axles of wheelsets at the site of the final inspection by the two-dimensional codes applied to them. The system should provide automatic search, reading and recognition of a two-dimensional code punching on the axis. The recognition result should be automatically transmitted to the ultrasound diagnostic unit as an identifier of the controlled object.
-
Product
PXIe-5672, 2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator
779900-02
-
2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator —The PXIe‑5672 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5672 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee.
-
Product
Performance And Load Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Performance Testing or load testing both are basically the processes of measuring the Stability, Scalability, Speed, responsiveness under various load environments. It is the testing performed for the identification of bottlenecks or users response time problems and its reasons. Performance Testing assists your system to reach consistency and provide the exact outcome according to your business needs.
-
Product
Ground Fault Monitor
IFT-120
-
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
Product
Veterinary Hematology Analyzer
ABX Micros ESV 60
-
The Gold Standard of Veterinary Hematology Testing- Open Tube- 10 animal species- 8 or 18 parameters- 50 tests/hour- Highly compact and lightweight- Micro-sampling on whole blood: 10μL- Precise cellular identification through electronic impedance variation method- Haemoglobin measurement with photometry
