Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Board-to-FPC Connector for 5G Millimeter-Wave Antenna Modules
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-To-FPC Connector for 5G Millimeter-Wave Antenna Modules offer good SI/EMI/EMS characteristics for high-frequency applications and features our industry-leading Tough Contact construction that achieves high contact reliability and retention force. Tough against shock impact by misalignment, the fully-shielded structure in both socket and header significantly improves EMI characteristics necessary for RF applications such as 5G.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Automotive Tester
-
An automotive tester can be used to inspect one or more aspects of an automobile. For example, a borescope automotive tester is an automotive inspection camera used by auto body mechanics to see inside car, truck and other vehicle engines before removing any engine parts. Other kinds of automotive tester devices are used to adjust belt tension, test the electronic ignition starter, search for air conditioning leaks, measure the force required to press a brake pedal, determine the antifreeze concentration, or check the paint thickness over collision repairs.PCE Instruments (PCE) offers a wide variety of automotive tester products. These diagnostic support tools help professional automobile mechanics identify a number of vehicle repair needs. PCE's automotive tester products can aid in the diagnosis of many different mechanical and electrical system issues, including but not limited to locating the cause of an engine misfire, testing fuel injector resistance, pinpointing an engine coolant leak, or detecting car cylinder head problems. It's no wonder so many auto repair technicians choose to stock theirs shops and garages with PCE automotive tester products.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
-
Product
Dynamic Mechanical Analyzer
DMA/SDTA 1 +
-
The METTLER TOLEDO DMA/SDTA1+ sets new standards in the market. In comparison with conventional DMA instruments it offers new and unique performance benefits: A frequency range up to 1000 Hz for material behavior simulation and accurate determination of moduli through the presence of a dedicated force sensor. Unique measurement of both displacement and force results in a very accurate determination of moduli. Wide force range from 1 mN to 40 N allows you to measure very soft and very stiff samples
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
Spring Probe
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
Product
Triaxial Linear Accelerometers
-
Columbia Research Laboratories
The Triaxial Force Balance Linear Accelerometers range from general purpose, low cost sensors, capable of measuring DC and low frequency acceleration simultaneously in three axes, to Miniature Airborne, Highly Reliable Sensors that operate from +24 to +32VDC Aircraft power. Also offered are compact, premium performance, extremely rugged sensors, well suited for demanding missile and airborne applications.
-
Product
Precision Positioning stage
N-661
-
Physik Instrumente GmbH & Co. KG
Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-1I8-6
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
-
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
Product
Manual Drive Unit
ATE MA350
-
Parallel contact stroke: 20 mm. Contact force max.: 300 N. Component on PCB: 58 mm. Pressure frame unit-opening angle: 66.Weight: 2,60 kg
-
Product
Pulse Heat Unit (Hot Bar Bonder)
-
*This method is most suitable for reliable soldering and thermo-compression because heating and cooling are done applying the pressure force*Good repeatability of heating temperature and time requires no skilled workers*Partial heating in short time allows to reduce thermal damages*For implement of Pb free
-
Product
Steel Structure Analyzer
NOVOTEST KRC-M2 (Coercive Force Meter)
-
Steel Structure Analyzer NOVOTEST KRC-M2 is designed for measuring coercive force of metal products in accordance with IEC 60404-7 and is used for non-destructive testing of chemical-thermal, thermal and thermomechanical treatments, evaluation of mechanical properties and residual stresses.
-
Product
PCB Test Fixture Kits
-
Emergent's fixture kits are available in bottom and double sided probing versions. They are fully scalable, from compact benchtop testers to full size multi-UUT production floor models. The removable, interchangeable plate design allows you to easily add and move test points, or swap out plates to test a completely different product. Each kit comes with a standard linear collapse over-clamp. A cam-follower closing system can be specified for higher force applications. Our fixture kits are manufactured using industrial grade phenolic laminate, which is similar to G10 in hardness and strength but easier to machine. The standard kit comes pre-assembled with blank plates for machining.
-
Product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
-
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
TorqueMate® Torque Analyzer
PTT-Series
-
The PTT torque meter makes quality documentation faster and easier. As an advanced torque controlling, monitoring and documentation solution, the torque analyzer enables operators and engineers to ensure product quality, safety and reliability promptly in a variety of manufacturing environments. The portable torque meters are designed for measuring torque, torque calibration, joint testing, auditing or force and load measurement. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures. Using a quality torque tester makes a safer world through accuracy and precision.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1B-4
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Portable Hardness Tester
Magnetic Type QualiMag Series
-
The Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester Rockwell test head fixes to the surface of iron and steel parts to test the hardness by applying magnetic force. Meant to replace Leeb hardness testers which are not as accurate nor reliable. Use the Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester on steel parts, steel plates, steel pipes, forgings, large to medium sized heat treated parts(if surface available), welding joints, pressure vessels, etc. The Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester Rockwell complies with Standards ISO 6508 and ASTM E18.
-
Product
Mission Management Systems
-
Installed on a variety of platforms, the HeliC3om™, Advanced C4I and Mission Management System, is combat proven and developed by active pilots whose first-hand combat experience is incorporated into all facets of the system. Our technology keeps all elements updated in real time with inputs from networked C4I sources. Pilots and crew easily receive and transmit video and data to/from all forces while updating maneuver, air, and naval units.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1L18-4
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Precise Temperature Forcing System
TA-5000A Series
-
The ThermalAir TA-5000 Series of temperature forcing systems bring precise thermal testing capabilities directly to your test application, exactly localizing to where thermal conditioning temperature cycling is required. ThermalAir TA-5000 temperature systems provide flexible thermal test solutions for an array of products and technologies.
-
Product
Vertical Probe Cards
B3
-
The patent-pending B3™ structure requires a minimum number of parts and can handle up to 300 probes. This vertical technology can provide: • Increased Uptime • Extended Probe Lifetime • Reduced Maintenance • Lower Cost of TestThe B3™ is an ideal solution for testing small pads and the low force probes minimize scrub. Planarity also remains stable over time increasing probe card life. Contact your sales representative to learn more about our B3™ probe cards.
-
Product
Standard Flexiforce Sensors for Force Measurement
FlexiForce
-
FlexiForce force sensors are ultra-thin and flexible printed circuits, which can be easily integrated into force measurement applications. These sensors are available for purchase in our online store.
-
Product
Rugged, Long Gauge Length Extensometers
Model 3543
-
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
Product
Audio Testing
-
Sound Power testing is required in many international standards. Quest also offers a variety of additional acoustic tests and the design experience to help you develop quieter products for your customers. Our chamber is able to cancel out all outside forces as well with its free floating floor boards.
